DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2A00 | Calculated value of air-fuel ratio (A/F) sensor response rate deterioration level less than threshold (2 trip detection logic) |
|


![]() |

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1 S1 (A/F) | +25% | Rich | Less than 3.0 |
| -12.5% | Lean | More than 3.35 | |
| O2S B1 S2 (HO2) | +25% | Rich | More than 0.5 |
| -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output voltage Almost no reaction | ![]() | ||
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2A00 | A |
| P2A00 and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C15 A/F sensor connector.
Measure the resistance between the terminals of the A/F sensor connector.
| Tester Connection | Specified Condition |
| HA1A (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HA1A (1) - A1A- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the C15 A/F sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connection | Specified Condition |
| +B (C15-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the C24 ECM connector.
Measure the resistance between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| HA1A (C15-1) - HA1A (C24-109) | Below 1 Ω |
| A1A+ (C15-3) - A1A+ (C24-112) | Below 1 Ω |
| A1A- (C15-4) - A1A- (C24-113) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (C15-1) or HA1A (C24-109) - Body ground | 10 kΩ or higher |
| A1A+ (C15-3) or A1A+ (C24-112) - Body ground | 10 kΩ or higher |
| A1A- (C15-4) or A1A- (C24-113) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
| Display (DTC Output) | Proceed to |
| P2A00 | A |
| No output | B |
|
| ||||
| A | |
| 6.REPLACE AIR-FUEL RATIO SENSOR |
| NEXT | |
| 7.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2A00 | B |
|
| ||||
| A | ||
| ||