REAR POWER WINDOW SWITCH > INSPECTION |
| 1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (for Models with Jam Protection Function on Driver Door Window Only) |
![]() |
Remove the power window switch.
Measure the resistance when the switch is operated according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (D) - 2 (SD) | UP | Below 1 Ω |
| 3 (B) - 4 (U) | Below 1 Ω | |
| 1 (D) - 2 (SD) | OFF | Below 1 Ω |
| 4 (U) - 5 (SU) | Below 1 Ω | |
| 4 (U) - 5 (SU) | DOWN | Below 1 Ω |
| 1 (D) - 3 (B) | Below 1 Ω |
| 2. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (for Models with Jam Protection Function on Driver Door Window Only) |
![]() |
Remove the power window switch.
Measure the resistance when the switch is operated according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (D) - 2 (SD) | UP | Below 1 Ω |
| 3 (B) - 4 (U) | Below 1 Ω | |
| 1 (D) - 2 (SD) | OFF | Below 1 Ω |
| 4 (U) - 5 (SU) | Below 1 Ω | |
| 4 (U) - 5 (SU) | DOWN | Below 1 Ω |
| 1 (D) - 3 (B) | Below 1 Ω |
| 3. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows) |
![]() |
Check the switch function.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (UP) - 1 (GND) | Auto up or up position | Below 1 Ω |
| 7 (DOWN) - 1 (GND) | Auto down or down position | Below 1 Ω |
| 8 (AUTO) - 1 (GND) | Auto up or auto down position | Below 1 Ω |
| 6 (UP) - 1 (GND) | Free | 10 kΩ or higher |
| 7 (DOWN) - 1 (GND) | Free | 10 kΩ or higher |
| 8 (AUTO) - 1 (GND) | Free | 10 kΩ or higher |
![]() |
Check that the LED illuminates.
Apply battery voltage to the power window regulator switch assembly and check that the LED illuminates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 4 (LED) Battery negative (-) → 1 (GND) | LED illuminates |
| 4. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows) |
![]() |
Check the switch function.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (UP) - 1 (GND) | Auto up or up position | Below 1 Ω |
| 7 (DOWN) - 1 (GND) | Auto down or down position | Below 1 Ω |
| 8 (AUTO) - 1 (GND) | Auto up or auto down position | Below 1 Ω |
| 6 (UP) - 1 (GND) | Free | 10 kΩ or higher |
| 7 (DOWN) - 1 (GND) | Free | 10 kΩ or higher |
| 8 (AUTO) - 1 (GND) | Free | 10 kΩ or higher |
![]() |
Check that the LED illuminates.
Apply battery voltage to the power window regulator switch assembly and check that the LED illuminates.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 4 (LED) Battery negative (-) → 1 (GND) | LED illuminates |