Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM

REAR VIEW MONITOR SYSTEM > TERMINALS OF ECU

for Preparation Click here



REAR TELEVISION CAMERA ASSEMBLY (w/o Entry and Start System)


  1. Disconnect the S19 connector from the rear television camera assembly.


    E183757E03

  2. Measure the voltage of each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S19-1 (CGND) - Body ground
    Shield - Body ground
    Ground
    Always
    Below 1 V
    S19-5 (CB+) - S19-1 (CGND)
    B - Shielded
    Power source
    Ignition switch ON
    Shift lever in R
    5.5 to 7 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the S19 connector to the rear television camera assembly.

  4. Check for pulses between each terminal of the connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S19-6 (CV+) - S19-2 (CV-)
    R - W
    Display signal
    Ignition switch ON
    Shift lever in R
    Under normal conditions
    Pulse generation
    (See waveform 1)
    Ignition switch ON
    Shift lever in R
    Camera lens covered, blacking out screen
    Pulse generation
    (See waveform 2)
    If the result is not as specified, the camera may have a malfunction.



  5. E171712E01
  6. Reference (Oscilloscope waveform):

    1. Waveform 1 (under normal conditions)
      Item
      Content
      Terminal No. (Symbol)
      S19-6 (CV+) - S19-2 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2 (camera lens is covered, blacking out the screen)
      Item
      Content
      Terminal No. (Symbol)
      S19-6 (CV+) - S19-2 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *1
      Waveform 1 (under normal conditions)
      *2
      Waveform 2 (camera lens is covered, blacking out the screen)
      *3
      Synchronized Signal
      *4
      Video Waveform


REAR TELEVISION CAMERA ASSEMBLY (w/ Entry and Start System)


  1. Disconnect the connector from the rear television camera assembly.


    E104829

  2. Measure the voltage of each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Terminal Description
    Condition
    Specified Condition
    6 (CGND) - Body ground
    Ground
    Always
    Below 1 V
    3 (CB+) - 6 (CGND)
    Power source
    Ignition switch ON
    Shift lever in R
    5.5 to 7 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the connector to the rear television camera assembly.

  4. Check for pulses between each terminal of the connector.

    Terminal No. (Symbol)
    Terminal Description
    Condition
    Specified Condition
    1 (CV+) - 4 (CV-)
    Display signal
    Ignition switch ON
    Shift lever in R
    Under normal conditions
    Pulse generation
    (See waveform 1)
    Ignition switch ON
    Shift lever in R
    Camera lens covered, blacking out screen
    Pulse generation
    (See waveform 2)

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    If the result is not as specified, the camera may have a malfunction.



  5. E171712E01
  6. Reference (Oscilloscope waveform):

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


    1. Waveform 1 (under normal conditions)
      Item
      Content
      Terminal No. (Symbol)
      1 (CV+) - 4 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2 (camera lens is covered, blacking out the screen)
      Item
      Content
      Terminal No. (Symbol)
      1 (CV+) - 4 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *1
      Waveform 1 (under normal conditions)
      *2
      Waveform 2 (camera lens is covered, blacking out the screen)
      *3
      Synchronized Signal
      *4
      Video Waveform


NAVIGATION RECEIVER ASSEMBLY (Click here)