Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW REGULATOR MOTOR

POWER WINDOW REGULATOR MOTOR > INSPECTION

for Preparation Click here



1. INSPECT POWER WINDOW REGULATOR MOTOR (PASSENGER SIDE) (for Models with Jam Protection Function on Driver Door Window Only)


    B127536E02
  1. Apply battery voltage to the motor connector according to the table below.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

    Standard:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 2
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1
    Motor gear rotates counterclockwise



2. INSPECT POWER WINDOW REGULATOR MOTOR (DRIVER SIDE) (for Models with Jam Protection Function on Driver Door Window Only)


    B137055E01
  1. Apply battery voltage to the motor connector according to the table below.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1, 2, 4, 7 and 10.

    Standard:
    Switch Condition
    Measurement Condition
    Specified Condition
    Manual Operation
    Battery positive (+) → Terminal 2 (PWR)
    Battery negative (-) → Terminal 1 (E), 7 (DN)
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2 (PWR)
    Battery negative (-) → Terminal 1 (E), 10 (UP)
    Motor gear rotates counterclockwise
    Auto Operation
    Battery positive (+) → Terminal 2 (PWR)
    Battery negative (-) → Terminal 1 (E), 4 (AUTO), 7 (DN)
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2 (PWR)
    Battery negative (-) → Terminal 1 (E), 4 (AUTO) 10 (UP)
    Motor gear rotates counterclockwise



3. INSPECT POWER WINDOW REGULATOR MOTOR (REAR RH) (for Models with Jam Protection Function on Driver Door Window Only)


    B127536E02
  1. Apply battery voltage to the motor connector according to the table below.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

    Standard:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 2
    Motor gear rotates counterclockwise



4. INSPECT POWER WINDOW REGULATOR MOTOR (REAR LH) (for Models with Jam Protection Function on Driver Door Window Only)


    B127535E01
  1. Apply battery voltage to the motor connector according to the table below.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

    Standard:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 2
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal
    Motor gear rotates counterclockwise



5. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows)


    B219211E01
  1. except TMC Mode:
    Apply positive (+) battery voltage to connector terminal 2 (B).

    NOTICE:
    Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows:

    OK:

    Measurement Condition
    Specified Condition
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
    3. Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.
    Motor gear rotates clockwise (Up)
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
    3. Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.
    Motor gear rotates counterclockwise (Down)

    1. If the result is not as specified, replace the front power window regulator motor assembly LH.

    CAUTION:
    Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



6. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows)


    B219210E01
  1. except TMC Mode:
    Apply positive (+) battery voltage to connector terminal 2 (B).

    NOTICE:
    Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows:

    OK:

    Measurement Condition
    Specified Condition
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
    3. Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.
    Motor gear rotates counterclockwise
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
    3. Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.
    Motor gear rotates clockwise

    1. If the result is not as specified, replace the front power window regulator motor assembly RH.

    CAUTION:
    Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



7. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Side) (for Models with Jam Protection Function on 4 Windows)


    B219210E03
  1. except TMC Mode:
    Apply positive (+) battery voltage to connector terminal 2 (B).

    NOTICE:
    Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows:

    OK:

    Measurement Condition
    Specified Condition
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
    3. Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.
    Motor gear rotates clockwise
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
    3. Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.
    Motor gear rotates counterclockwise

    1. If the result is not as specified, replace the rear power window regulator motor assembly (for rear LH side).

    CAUTION:
    Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



8. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Side) (for Models with Jam Protection Function on 4 Windows)


    B219211E03
  1. except TMC Mode:
    Apply positive (+) battery voltage to connector terminal 2 (B).

    NOTICE:
    Do not apply positive (+) battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows:

    OK:

    Measurement Condition
    Specified Condition
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
    3. Disconnect and reconnect a negative (-) battery lead to terminal 10 (UP) within 1 second.
    Motor gear rotates counterclockwise
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
    3. Disconnect and reconnect a negative (-) battery lead to terminal 7 (DOWN) within 1 second.
    Motor gear rotates clockwise

    1. If the result is not as specified, replace the rear power window regulator motor assembly (for rear RH side).

    CAUTION:
    Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



9. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows)


    B219204E01
  1. for TMC Mode:
    Apply battery voltage to the motor connector according to the table below.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1, 2, 4, 7 and 10.

    Standard:
    Switch Condition
    Measurement Condition
    Specified Condition
    Manual Operation
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 7 (DOWN)
    Motor gear rotates counterclockwise
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 10 (UP)
    Motor gear rotates clockwise
    Auto Operation
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 7 (DOWN)
    Motor gear rotates counterclockwise
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 10 (UP)
    Motor gear rotates clockwise

    If the result is not as specified, replace the front power window regulator motor assembly LH.



10. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows)


    B219205E01
  1. for TMC Mode:
    Apply battery voltage to the motor connector according to the table below.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1, 2, 4, 7 and 10.

    Standard:
    Switch Condition
    Measurement Condition
    Specified Condition
    Manual Operation
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 7 (DOWN)
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 10 (UP)
    Motor gear rotates counterclockwise
    Auto Operation
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 7 (DOWN)
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 4 (AUTO) 10 (UP)
    Motor gear rotates counterclockwise

    If the result is not as specified, replace the front power window regulator motor assembly RH.



11. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Side) (for Models with Jam Protection Function on 4 Windows)


    B219205E03
  1. for TMC Mode:
    Apply battery voltage to the motor connector according to the table below.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1, 2, 4, 7 and 10.

    Standard:
    Switch Condition
    Measurement Condition
    Specified Condition
    Manual Operation
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 7 (DOWN)
    Motor gear rotates counterclockwise
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 10 (UP)
    Motor gear rotates clockwise
    Auto Operation
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 7 (DOWN)
    Motor gear rotates counterclockwise
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 10 (UP)
    Motor gear rotates clockwise

    If the result is not as specified, replace the rear power window regulator motor assembly (for rear LH side).



12. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Side) (for Models with Jam Protection Function on 4 Windows)


    B219204E03
  1. for TMC Mode:
    Apply battery voltage to the motor connector according to the table below.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1, 2, 4, 7 and 10.

    Standard:
    Switch Condition
    Measurement Condition
    Specified Condition
    Manual Operation
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 7 (DOWN)
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 10 (UP)
    Motor gear rotates counterclockwise
    Auto Operation
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 7 (DOWN)
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2 (B)
    Battery negative (-) → Terminal 1 (GND), 4 (AUTO), 10 (UP)
    Motor gear rotates counterclockwise

    If the result is not as specified, replace the rear power window regulator motor assembly (for rear RH side).