SEAT BELT WARNING SYSTEM > Front Passenger Side Seat Belt Warning Light Malfunction |

| 1.CHECK WIRE HARNESS (BATTERY POSITIVE AND BODY GROUND) |
![]() |
Disconnect the clock assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F3-3 (IG) - Body ground | Ignition switch ON | 10 to 14 V |
| Tester Connection | Condition | Specified Condition |
| F3-19 (GND1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 2.CHECK CLOCK ASSEMBLY |
![]() |
Disconnect the clock assembly connector.
Apply battery voltage to the connector according to the table below.
| Condition | Specified Condition |
| Battery positive (+) → Terminal 3 (IG) Battery negative (-) → Terminal 10 (PBEW), 19 (GND1) | Lights up (Seat belt warning light) |
|
| ||||
| OK | |
| 3.CHECK WIRE HARNESS (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY) |
![]() |
Disconnect the combination meter assembly and clock assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F1-9 (P/SB) - F3-10 (PBEW) | Always | Below 1 Ω |
| F1-9 (P/SB) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION COVER) |
![]() |
Disconnect the occupant detection sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-1 - A-3 | The passenger seat is occupied | Below 100 Ω |
| A-1 - A-3 | The passenger seat is not occupied | Below 1 MΩ |
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY) |
![]() |
Disconnect the combination meter assembly and front seat inner belt assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F2-8 (PBKL) - O22-1 | Always | Below 1 Ω |
| F2-8 - Body ground | Always | 10 kΩ or higher |
| O22-3 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| F2-8 (PBKL) - T12-1 | Always | Below 1 Ω |
| F2-8 - Body ground | Always | 10 kΩ or higher |
| T12-3 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| F2-8 (PBKL) - N30-1 | Always | Below 1 Ω |
| F2-8 - Body ground | Always | 10 kΩ or higher |
| N30-3 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| F2-8 (PBKL) - U9-1 | Always | Below 1 Ω |
| F2-8 - Body ground | Always | 10 kΩ or higher |
| U9-3 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.REPLACE FRONT SEAT INNER BELT ASSEMBLY (FRONT PASSENGER SIDE) |
Replace the front seat inner belt assembly (front passenger side)
|
| ||||
| OK | ||
| ||