CLUTCH PEDAL > INSTALLATION |
| 1. INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSHING |
![]() |
Apply MP grease to the inside of a new clevis bushing.
Install the clevis bushing to the clutch pedal.
| 2. INSTALL CLUTCH PEDAL TURNOVER BUSHING (for LHD) |
![]() |
Apply MP grease to the inside of the turnover bushing.
Install the turnover bushing to the clutch pedal.
| 3. INSTALL CLUTCH PEDAL TURNOVER BUSHING (for RHD) |
![]() |
Apply MP grease to the inside of the turnover bushing.
Install the turnover bushing to the clutch pedal.
| 4. INSTALL NO. 1 CLUTCH PEDAL CUSHION (for LHD) |
![]() |
Using needle-nose pliers, install the 2 No. 1 clutch pedal cushions to the clutch pedal.
| 5. INSTALL NO. 1 CLUTCH PEDAL CUSHION (for RHD) |
![]() |
Using needle-nose pliers, install the 2 No. 1 clutch pedal cushions to the clutch pedal.
| 6. INSTALL CLUTCH PEDAL BUSHING |
![]() |
Apply MP grease to the inner, outer and end surfaces of 2 new pedal bushings.
Install the clutch pedal shaft collar and 2 pedal bushings to the clutch pedal.
| 7. INSTALL CLUTCH PEDAL PAD |
Install the clutch pedal pad to the clutch pedal.
| 8. INSTALL CLUTCH PEDAL SPRING HOLDER |
![]() |
Apply MP grease to the inside of a new clutch pedal spring holder.
Install the clutch pedal spring holder.
| 9. INSTALL CLUTCH PEDAL SUB-ASSEMBLY |
![]() |
Install the clutch pedal to the clutch pedal support with the bolt and nut.
| 10. INSTALL PEDAL WITH HOOK SPRING |
![]() |
Apply MP grease to the sliding portion of the spring.
Install the hook spring.
| 11. INSTALL TORSION SPRING |
![]() |
Apply MP grease to the sliding portion of the spring.
Install the torsion spring.
| 12. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY (for LHD) |
![]() |
Install the clutch pedal support to the vehicle with the 2 nuts and bolt.
| 13. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY (for RHD) |
![]() |
Install the clutch pedal support to the vehicle with the 3 nuts and bolt.
| 14. INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS PIN |
![]() |
Apply MP grease to the contact surface of the pin and clevis bushing.
Connect the clevis to the clutch pedal with the pin and a new clip.
| 15. CONNECT CONNECTORS |
Connect the clutch start switch connector.
Connect the clutch switch connector (with cruise control).
| 16. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Connect each connector.
Install the combination meter assembly with the 4 screws <E>.
| 17. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
Engage the guide and the 4 claws.
Install the instrument cluster finish panel with the 2 clips.
| 18. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL |
![]() |
Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.
| 19. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY |
Connect each connector.
![]() |
Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.
| 20. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Install the air hose and connect the connector.
Engage the 2 claws and the DLC3.
Engage the claw and the 4 clips.
Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.
| 21. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the cowl side trim clip.
| 22. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.
| 23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 24. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY |