Home › TRANSMISSION ยท E351 MANUAL TRANSAXLE › TRANSMISSION CONTROL CABLE

TRANSMISSION CONTROL CABLE > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B137272
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



3. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226063
  1. Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.



4. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226064
  1. Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.



5. REMOVE UPPER CONSOLE PANEL


    B137274E01
  1. Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.



    B137275
  1. Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.

  1. with Seat Heater System:

    1. Disconnect each connector.



6. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY


    B137277
  1. Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.



7. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY


    C132951
  1. Remove the 2 clips and disconnect the end of the transmission control cable.



    C135402E01
  1. Pull out the control cable assembly locks.

  1. Turn the adjust nut 180° clockwise. While holding the adjust nut, separate the control cable assembly.



8. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here.


9. REMOVE AIR CONDITIONER UNIT ASSEMBLY
Click here.


10. REMOVE CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn back the carpet.



    C133884
  1. Disconnect the holder (with connectors).

  1. Remove the 3 bolts and center airbag sensor assembly.



11. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    A134904
  1. Remove the 2 nuts and cover.



12. REMOVE AIR CLEANER INLET ASSEMBLY


    A134903
  1. Remove the 2 bolts, clamp and air cleaner inlet.



13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A135666E01
  1. Disconnect the mass air flow meter connector (*1).

  1. Disconnect the purge VSV connector (*2).

  1. Disconnect the 2 purge VSV vacuum hoses (*3).

  1. Disconnect the purge line hose from the clamp (*4).



    A135667E01
  1. Disconnect the No. 2 ventilation hose from the air cleaner hose.



    A135668
  1. Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.



    A135669
  1. Remove the 2 bolts and air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.



14. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A134905
  1. Disconnect the hose clamp.

  1. Remove the 3 bolts and air cleaner case.



15. REMOVE BATTERY


    A134906
  1. Loosen the bolt and nut, and remove the battery clamp.

  1. Remove the battery and battery tray.



16. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY


    C132952
  1. Remove the 2 clips and 2 washers and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.



    C135401
  1. Remove the 2 bolts and control cable assembly.

  1. Remove the No. 2 shift cable grommet retainer from the control cable assembly.