DTC P0796 Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) |
| DTC No. | DTC Detecting Condition | Trouble Area |
| P0796 | The engine revs freely when 2nd or 6th gear is requested (2-trip detection logic) When the following is detected twice (2-trip detection logic):
|
|
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0796) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the intelligent tester on.
Enter the following items: "Powertrain / ECT / DTC / Current or Pending".
Read the DTCs using the intelligent tester.
| Display (DTC output) | Proceed to |
| Only "P0796" is output | A |
| "P0796" and other DTCs | B |
|
| ||||
| B | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Start the engine and turn the intelligent tester on.
Enter the following items: "Powertrain / ECT / Active Test / Control the Shift Position".
| Item | Test Details | Diagnostic Note |
| Control the Shift Position | [Test Details] Operate the shift solenoid valve and set each shift position by yourself. [Others]
| Possible to check the operation of the shift solenoid valves. |
Check the vehicle speed and the gear position when the engine speed is 1,000 rpm.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the TCM gear shift command and the actual gear position.
| Actuator gear position under malfunction | TCM gear shift command | Proceed to | ||||||
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Shift solenoid SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1
| N*1
| N*1
| N*1
| 5th | 6th | ||
| Shift solenoid SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1
| N*1
| ||
| Shift solenoid SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1
| ||
| Shift solenoid SL4 | Stuck ON*3
| 3rd | 3rd | 3rd | 4th | 5th | 5th | D |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1
| 6th | ||
| Shift solenoid SLT | Stuck ON | N*2
| N*2
| N*2
| N*2
| N*2
| N*2
| E |
| Stuck OFF*3
| 1st | 2nd | 3rd | 4th | 5th | 6th | ||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| C | |
| 3.INSPECT SHIFT SOLENOID VALVE (SL3) |
![]() |
Remove the shift solenoid valve SL3.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| 1 - 2 | 5.0 to 5.6 Ω |
Connect a positive (+) lead through a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
|
| ||||
| OK | |
| 5.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
|
| ||||
| OK | ||
| ||