Home › TRANSMISSION ยท U660E AUTOMATIC TRANSAXLE › DIFFERENTIAL OIL SEAL

DIFFERENTIAL OIL SEAL > REMOVAL

for Preparation Click here



1. DRAIN AUTOMATIC TRANSAXLE FLUID


    C142572
  1. Remove the refill plug and gasket.



    C142571
  1. Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket.



    C142574
  1. Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube.

  1. Drain the automatic transaxle fluid.



    C142574
  1. Using a 6 mm socket hexagon wrench, install the No. 1 transmission oil filler tube.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }



    C142571
  1. Using a 6 mm socket hexagon wrench, install the overflow plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    C142572
  1. Install the refill plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



2. REMOVE FRONT WHEELS


3. REMOVE FRONT AXLE HUB NUT LH


    C108168E02
  1. Using SST and a hammer, release the staked part of the front axle hub nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the thread of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.



4. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedures described for the LH side.



5. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


    C140591
  1. Remove the nut and separate the front stabilizer link assembly.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.



6. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



7. SEPARATE FRONT SPEED SENSOR LH


    C140592
  1. Remove the bolt and clip, and separate the speed sensor wire and flexible hose from the shock absorber.



    C132782E01
  1. Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.



8. SEPARATE FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.



9. SEPARATE TIE ROD ASSEMBLY LH


    C108515E02
  1. Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end sub-assembly from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Make sure that the string of the SST is securely tied to the vehicle.
    2. Be careful not to damage the ball joint dust cover.
    3. Be careful not to damage the steering knuckle.
    4. Be careful not to damage the front disc brake dust cover.



10. SEPARATE TIE ROD ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



11. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM LH


    F040142E01
  1. Remove the bolt and 2 nuts, and separate the front suspension lower No. 1 arm from the lower ball joint.



12. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures described for the LH side.



13. SEPARATE FRONT AXLE ASSEMBLY LH


    D032030E06
  1. Put matchmarks on the front drive shaft assembly and the axle hub.

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.



14. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



15. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    C083850E02
  1. Using SST, remove the front drive shaft assembly LH.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the drive shaft dust cover, boot, and oil seal.
    2. Be careful not to drop the drive shaft assembly.



16. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    C080304E03
  1. Using a screwdriver, remove the bearing bracket hole snap ring.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    Do not damage the boot and oil seal.



17. SECURE FRONT AXLE HUB SUB-ASSEMBLY


    F045045E03
  1. Secure the front axle hub bearing.

    SST
    09608-16042   (09608-02021, 09608-02041)

    NOTICE:
    The hub bearing may be damaged if it is subjected to the vehicle's full weight, such as moving the vehicle with the drive shaft removed. If it is necessary to place the vehicle's weight on the hub bearing, first support it with SST.



18. REMOVE TRANSAXLE CASE OIL SEAL


    C133598E01
  1. Using SST, remove the oil seal from the transaxle case.

    SST
    09308-00010  



19. REMOVE FRONT TRANSAXLE CASE OIL SEAL


    C133597E01
  1. Using SST, remove the oil seal from the transaxle housing.

    SST
    09308-00010