DIFFERENTIAL CASE > REASSEMBLY |
| 1. INSTALL FRONT DIFFERENTIAL SIDE GEAR |
![]() |
Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.
| 2. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT |
![]() |
Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.
| 3. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN |
![]() |
Using a pin punch and hammer, install the pinion shaft straight pin.
![]() |
Using a chisel and hammer, stake the differential case.
| 4. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a press, install the front differential case front tapered roller bearing to the differential case.
![]() |
Using SST and a hammer, install the front differential case front tapered roller bearing outer race to the transaxle housing.
| 5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, install the front differential case rear tapered roller bearing to the differential case.
![]() |
Using SST and a hammer, install the front differential case rear tapered roller bearing outer race to the transaxle housing.
| 6. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD |
![]() |
Install the differential assembly to the transaxle case.
![]() |
Clean the matching surfaces of the transaxle case and transaxle housing.
Install the transaxle housing to the transaxle case and tighten them with the 16 bolts.
![]() |
Using SST, turn the differential assembly right and left 2 or 3 times to settle the bearing.
Using SST and a torque wrench, measure the turning torque of the differential.
| Mark | Thickness | Mark | Thickness |
| 0 | 1.90 (0.0748) | A | 2.40 (0.0945) |
| 1 | 1.95 (0.0768) | B | 2.45 (0.0965) |
| 2 | 2.00 (0.0787) | C | 2.50 (0.0984) |
| 3 | 2.05 (0.0807) | D | 2.55 (0.1004) |
| 4 | 2.10 (0.0827) | E | 2.60 (0.1024) |
| 5 | 2.15 (0.0846) | F | 2.65 (0.1043) |
| 6 | 2.20 (0.0866) | G | 2.70 (0.1063) |
| 7 | 2.25 (0.0886) | H | 2.75 (0.1083) |
| 8 | 2.30 (0.0906) | J | 2.80 (0.1102) |
| 9 | 2.35 (0.0925) | - | - |
![]() |
Remove the 16 bolts and the transaxle housing.
![]() |
Remove the differential assembly.
| 7. INSTALL FRONT DIFFERENTIAL RING GEAR |
![]() |
Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).
Clean the contact surface of the front differential case.
![]() |
Align the matchmarks, and install the front differential ring gear case quickly.
![]() |
Tighten the 10 bolts.
| 8. INSTALL TRANSAXLE HOUSING OIL SEAL |
![]() |
Using SST and a hammer, drive in a new oil seal.
Coat the lip of the oil seal with a small amount of MP grease.
| 9. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL |
![]() |
Using SST and a hammer, drive in a new oil seal.
Coat the lip of the oil seal with a small amount of MP grease.