Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Rear Fog Light Circuit

for Preparation Click here


DESCRIPTION

When the taillights are on and the rear fog light switch is turned on, the main body ECU turns the rear fog lights on.

WIRING DIAGRAM


E121535E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Turn the light control switch to the TAIL position.

  1. Select the item below in the ACTIVE TEST and then check that the relay operates.

    Main Body (Main Body ECU): 
    Item
    Test Details
    Diagnostic Note
    Rear Fog Light Relay
    Rear fog light relay ON/OFF
    -

    OK:
    Rear fog light relay operates. (Rear fog lights come on)



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.INSPECT FUSE (RR FOG)
  1. Remove the RR FOG fuse from the engine room R/B.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


3.INSPECT REAR FOG LIGHT RELAY


    B060778E86
  1. Remove the rear fog light relay from the engine room No. 2 J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    Below 1 Ω (When battery voltage is applied to terminals 1 and 2)



NG
REPLACE REAR FOG LIGHT RELAY
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    E121538E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-14 - Body ground
    Light control switch in TAIL and rear fog light switch OFF → ON
    10 to 14 V → Below 1 V



OK
Go to step 7
NG


5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B ASSEMBLY - REAR FOG LIGHT RELAY)


    E133233E01
  1. Remove the rear fog light relay from the engine room No. 2 relay block.

  1. Measure the voltage on the relay block side according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Rear fog light relay terminal 2 - Body ground
    Light control switch OFF → TAIL
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - MAIN BODY ECU)


    E121537E04
  1. Disconnect the E8 main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-14 - Body ground
    Light control switch OFF → TAIL
    Below 1 V → 10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 

7.CHECK HARNESS AND CONNECTOR (BATTERY - REAR FOG LIGHT RELAY)


    E133233E02
  1. Remove the rear fog light relay from the engine room No. 2 relay block.

  1. Measure the voltage on the relay block side according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Rear fog light relay terminal 5 - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - REAR FOG LIGHT RELAY)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR FOG LIGHT RELAY - BODY GROUND)