CLUTCH MASTER CYLINDER > INSTALLATION |
| 1. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY (for LHD) |
![]() |
Install a new gasket to the clutch master cylinder assembly.
Install the clutch master cylinder with the 2 nuts.
| 2. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY (for RHD) |
![]() |
Install a new gasket to the clutch master cylinder assembly.
Install the clutch master cylinder with the 2 nuts.
| 3. CONNECT CLUTCH LINE |
![]() |
Using SST, connect the clutch line.
| 4. CONNECT CLUTCH RESERVOIR TUBE |
![]() |
Connect the clutch reservoir tube to the clutch master cylinder with the clip.
| 5. CONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS |
![]() |
Apply MP grease to the contact surface of the pin and clevis bushing.
Connect the clevis to the clutch pedal with the pin and a new clip.
| 6. INSTALL BRAKE BOOSTER ASSEMBLY (for LHD) |
| 7. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Connect each connector.
Install the combination meter assembly with the 4 screws <E>.
| 8. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
Engage the guide and the 4 claws.
Install the instrument cluster finish panel with the 2 clips.
| 9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL |
![]() |
Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.
| 10. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY |
Connect each connector.
![]() |
Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.
| 11. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Install the air hose and connect the connector.
Engage the 2 claws and the DLC3.
Engage the claw and the 4 clips.
Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.
| 12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the cowl side trim clip.
| 13. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.
| 14. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY |
![]() |
Install the outer cowl top panel sub-assembly with the 4 bolts and 4 nuts.
| 15. INSTALL WIND SHIELD WIPER LINK ASSEMBLY |
| 16. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for LHD) |
![]() |
Install the air cleaner case with the 3 bolts.
Connect the hose clamp.
| 17. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for LHD) |
Install the air cleaner filter element onto the air cleaner case.
![]() |
Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.
![]() |
Align the matchmarks of the No. 1 air cleaner hose and throttle body, and then connect the air cleaner hose No. 1 to the throttle body and unfasten the No. 1 air cleaner hose clamp.
![]() |
Connect the No. 2 ventilation hose to the air cleaner hose.
![]() |
Connect the purge line hose to the clamp (*1).
Connect the 2 purge VSV vacuum hoses (*2).
Connect the purge VSV connector (*3).
Connect the mass air flow meter connector (*4).
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 19. BLEED CLUTCH PIPE LINE |
Fill the brake reservoir with brake fluid and bleed the clutch system.
| 20. CHECK BRAKE FLUID |
Check the brake fluid (Click here).
| 21. CHECK FLUID LEVEL IN RESERVOIR |
![]() |
Check the fluid level.
If brake fluid level is lowered, check for leakage and inspect the disc brake pad. If necessary, refill the reservoir with brake fluid after repair and replacement.
| 22. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY |