ROOF HEADLINING > INSTALLATION |
| 1. INSTALL NO. 1 ROOF WIRE (w/o Sliding Roof) |
Apply new double-sided tape to locations shown in the illustration while aligning the tape with the markings on the roof headlining.

Peel off the release paper from the double-sided tape.
Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.
Turn the visor connectors clockwise approximately 90° to install the connectors to the roof headlining.
Apply adhesive tape to locations shown in the illustration.

| 2. INSTALL NO. 1 ROOF WIRE (w/ Sliding Roof) |
Apply new double-sided tape to locations shown in the illustration while aligning the tape with the markings on the roof headlining.

Peel off the release paper from the double-sided tape.
Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.
Turn the visor connectors clockwise approximately 90° to install the connectors to the roof headlining.
Apply adhesive tape to locations shown in the illustration.

| 3. INSTALL ANTENNA CORD SUB-ASSEMBLY |
Apply new double-sided tape.

Remove the double-sided tape from the roof headlining assembly.
Peel off the appropriate amount of new double-sided tape. Be careful not to touch the adhesive surface.
Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.
Peel off the backing sheet from the double-sided tape.
Install the antenna cord to the roof headlining assembly from the front of the vehicle.

Put the strips of the tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.
| 4. INSTALL VANITY LIGHT ASSEMBLY |
![]() |
Engage the 3 claws and install the vanity light assembly.
| 5. INSTALL FASTENER HOOK (w/ Sliding Roof) |
![]() |
Align the markings on the roof headlining assembly with the fastener hooks and install the fastener hooks using hot melt glue as shown in the illustration.
| 6. INSTALL NO. 2 REAR SIDE RAIL SPACER LH (w/ Sliding Roof) |
![]() |
Align the markings on the roof headlining assembly with the No. 2 rear side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.
| 7. INSTALL NO. 2 REAR SIDE RAIL SPACER RH (w/ Sliding Roof) |
| 8. INSTALL NO. 4 ROOF SILENCER PAD (w/o Sliding Roof) |
![]() |
Align the markings on the roof headlining assembly with the No. 4 roof silencer pads and install the silencer pads using hot melt glue or double-sided tape as shown in the illustration.
| 9. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof) |
![]() |
Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the silencer pad using hot melt glue or double-sided tape as shown in the illustration.
| 10. INSTALL ROOF SIDE RAIL SILENCER PAD LH (w/o Sliding Roof) |
![]() |
Align the markings on the roof headlining assembly with the roof side rail silencer pad LH and install the silencer pad using hot melt glue as shown in the illustration.
| 11. INSTALL ROOF SIDE RAIL SILENCER PAD RH (w/o Sliding Roof) |
| 12. INSTALL NO. 3 REAR SIDE RAIL SPACER LH (w/o Sliding Roof) |
![]() |
Align the markings on the roof headlining assembly with the No. 3 rear side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.
| 13. INSTALL NO. 3 REAR SIDE RAIL SPACER RH (w/o Sliding Roof) |
| 14. INSTALL NO. 2 REAR SIDE RAIL SPACER LH (w/o Sliding Roof) |
![]() |
Align the markings on the roof headlining assembly with the No. 2 rear side rail spacer LH and install the spacer using hot melt glue as shown in the illustration.
| 15. INSTALL NO. 2 REAR SIDE RAIL SPACER RH (w/o Sliding Roof) |
| 16. INSTALL RADIO SETTING CONDENSER |
Using an air riveter or hand riveter with a nose piece, install the radio setting condenser with a new rivet.

| 17. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof) |
![]() |
Pull the roof headlining assembly into the vehicle through the rear left door.
Engage the 4 clips.
Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.
Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.
Install the radio setting condenser to the front pillar RH with the bolt.
Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.

| 18. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof) |
![]() |
Pull the roof headlining assembly into the vehicle through the rear left door.
Engage the hook, 4 clips, and 2 fasteners.
Connect the sliding roof drive gear connector.
Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.
Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.
Install the radio setting condenser to the front pillar RH with the bolt.
Connect the No. 1 roof wire connector and engage each clamp to the front pillar LH.

| 19. INSTALL SUNSHADE TRIM HOLDER (w/ Rear Sunshade) |
![]() |
Engage the 2 claws.
![]() |
Using a screwdriver, turn the pin of each sunshade trim holder 90°to install the sunshade trim holders.
| 20. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof) |
![]() |
Align the paint mark on the inner surface of the opening trim moulding with the notch of the roof headlining, and install the sun roof opening trim moulding so that joining point of the opening trim is on the left side of the vehicle as shown in the illustration.
| 21. INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof) |
![]() |
Push the light bulb holder in the direction indicated by the arrow in the illustration to engage the claw.
Engage the 4 claws.
![]() |
Engage the 6 claws and install the spot light assembly.
| 22. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof) |
![]() |
Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.
![]() |
Engage the 4 claws.
![]() |
Engage the 4 claws and install the lens cover.
| 23. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY |
![]() |
Assemble the front assist grip sub-assembly as shown in the illustration.
![]() |
Install the front assist grip sub-assembly.
| 24. INSTALL REAR ASSIST GRIP SUB-ASSEMBLY |
| 25. INSTALL VISOR HOLDER |
Engage the 2 claws.
Push in the visor holder and turn it approximately 45°as shown in the illustration.

| 26. INSTALL VISOR ASSEMBLY LH |
![]() |
Engage the 2 clips and install the visor assembly LH.
![]() |
Engage the 4 claws and install the visor bracket cover.
| 27. INSTALL VISOR ASSEMBLY RH |
| 28. INSTALL ROOF CONSOLE BOX ASSEMBLY |
![]() |
Connect the connectors.
Engage the 2 claws and 2 clips, and then install the roof console box assembly.
| 29. INSTALL FRONT PILLAR GARNISH LH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish LH.
Engage the 2 claws and 2 clips, then install the front pillar garnish LH.
| 30. INSTALL FRONT PILLAR GARNISH RH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish RH.
Engage the 2 claws and 2 clips, then install the front pillar garnish RH.
| 31. INSTALL ROOF SIDE INNER GARNISH LH |
![]() |
Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.
| 32. INSTALL ROOF SIDE INNER GARNISH RH |
| 33. INSTALL UPPER CENTER PILLAR GARNISH LH |
![]() |
Engage the clip.
Install the upper center pillar garnish LH with the bolt.
| 34. INSTALL LOWER CENTER PILLAR GARNISH LH |
![]() |
Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH.
| 35. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH |
![]() |
Install the floor end of the front seat outer belt assembly LH with the bolt.
| 36. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side) |
![]() |
Engage the 3 claws and install the lap belt outer anchor cover.
| 37. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Install the front door opening trim weatherstrip LH as shown in the illustration.
| 38. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the cowl side trim clip.
| 39. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.
| 40. INSTALL UPPER CENTER PILLAR GARNISH RH |
| 41. INSTALL LOWER CENTER PILLAR GARNISH RH |
| 42. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH |
| 43. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side) |
| 44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Install the front door opening trim weatherstrip RH as shown in the illustration.
| 45. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 46. INSTALL FRONT DOOR SCUFF PLATE RH |
| 47. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH |
![]() |
Engage the 3 claws to install the rear door inner glass weatherstrip.
| 48. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH |
![]() |
Engage the claw to install the No. 1 door scuff plate clamp.
Connect each connector.
![]() |
Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.
![]() |
Engage the 7 clips to install the rear door trim board to the rear door panel.
Install the 3 screws.
| 49. INSTALL DOOR ASSIST GRIP COVER LH |
![]() |
Engage the 6 claws and install the door assist grip cover.
| 50. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH |
![]() |
Engage the 3 claws to install the rear door inside handle bezel plug.
| 51. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH (for Reclining Seat Type) |
![]() |
Install the rear seat reclining control cable.
![]() |
Engage the 2 clips and claw and then install the reclining remote control lever sub-assembly.
Install the bolt.
![]() |
Adjust the control lever to set the rear reclining adjuster assembly to its upper most position.
Pull plate A toward the front of the vehicle to lock the plate.
| 52. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH (for Reclining Seat Type) |
| 53. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Install the rear door opening trim weatherstrip LH as shown in the illustration.
| 54. INSTALL REAR DOOR SCUFF PLATE LH |
![]() |
Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.
| 55. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Install the rear door opening trim weatherstrip RH as shown in the illustration.
| 56. INSTALL REAR DOOR SCUFF PLATE RH |
| 57. INSTALL CENTER SEATBACK ASSEMBLY (for Reclining Seat Type) |
![]() |
Install the center seatback assembly with the 2 bolts.
| 58. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type) |
![]() |
Install the separate type rear seatback assembly LH with the 2bolts and 2 nuts.
![]() |
Engage the 3 clamps and install the cover.
![]() |
Install the 2 rear seat belts.
| 59. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type) |
![]() |
Install the separate type rear seatback assembly RH with the 2 bolts and 2 nuts.
![]() |
Engage the 3 clamps and install the cover.
![]() |
Install the rear seat belt.
| 60. INSTALL REAR SEATBACK COVER (for Reclining Seat Type) |
| 61. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
![]() |
Install the rear side seatback assembly with the bolt.
| 62. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type) |
| 63. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
![]() |
Install the separate type rear seatback assembly with the 2 bolts.
| 64. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type) |
![]() |
Install the separate type rear seat back assembly with the 2 bolts.
| 65. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
| 66. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 67. INSTALL REAR SEAT CUSHION ASSEMBLY |
![]() |
Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.
Confirm that the seat cushion is firmly installed.
| 68. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat) |
Place the seat in the cabin.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
![]() |
Temporarily install the front side of the front seat assembly with the 2 bolts.
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
![]() |
Temporarily install the rear side of the front seat assembly with the 2 bolts.
Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
| 69. INSTALL INNER SEAT TRACK BRACKET COVER RH (for Power Seat) |
![]() |
Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the inner seat track bracket cover to engage claw B.
| 70. INSTALL SEAT TRACK COVER LH (for Power Seat) |
![]() |
Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the seat track cover to engage claw B.
| 71. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat) |
| 72. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat) |
Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.
Connect the connector and clamp.
Move the front seat assembly to the rearmost position by operating the slide handle.
![]() |
Temporarily install the front seat track bracket with the 2 bolts.
Move the front seat assembly fully forward by operating the slide handle.
![]() |
Temporarily install the rear seat track bracket with the 2 bolts.
Move the front seat assembly to the rearmost position by operating the slide handle.
Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.
Move the front seat assembly fully forward by operating the slide handle.
Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.
| 73. INSTALL INNER SEAT TRACK BRACKET COVER LH (for Manual Seat) |
![]() |
Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the seat track bracket cover inner to engage claw B.
| 74. INSTALL SEAT TRACK COVER LH (for Manual Seat) |
![]() |
Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the seat track cover to engage claw B.
| 75. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat) |
| 76. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat) |
| 77. INSTALL INNER SEAT TRACK BRACKET COVER LH (for Power Seat) |
| 78. INSTALL SEAT TRACK COVER RH (for Power Seat) |
| 79. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat) |
| 80. INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat) |
| 81. INSTALL INNER SEAT TRACK BRACKET COVER RH (for Manual Seat) |
| 82. INSTALL SEAT TRACK COVER RH (for Manual Seat) |
| 83. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat) |
| 84. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat) |
| 85. INSPECT SRS WARNING LIGHT |
| 86. INSPECT FRONT SEAT ASSEMBLY (for Power Seat) |
Check the power seat operation.
Check the seat heater operation (with seat heater system).
Turn the ignition switch on (IG).
Turn the seat heater switch ON.
Wait 5 minutes or more and confirm that the seat surface becomes warm.
| 87. INSPECT SLIDE ADJUSTER LOCK (for Manual Seat) |