ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System) > TERMINALS OF ECU |
| CHECK TRANSPONDER KEY AMPLIFIER |
Disconnect the E25 amplifier connector and measure the resistance between the terminal of the wire harness side connector and body ground.

| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (E25-7) - Body ground | V - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E25 amplifier connector and measure the resistance and voltage of each terminal of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| VC5 (E25-1) - AGND (E25-7) | O - V | Power source | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | 4.6 to 5.4 V | |||
| CODE (E25-4) - AGND (E25-7) | BR - V | Demodulated signal of key code data | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | Waveform 1 | |||
| TXCT (E25-5) - AGND (E25-7) | R - V | Key code output signal | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | Waveform 2 | |||
| AGND (E25-7) - Body ground | V - Body ground | Ground | Always | Below 1 Ω |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Terminal | CODE (E25-4) - AGND (E25-7) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Key is in ignition key cylinder |
![]() |
Waveform 2 (Reference)
| Terminal | TXCT (E25-5) - AGND (E25-7) |
| Tool Setting | 2 V/DIV., 10 ms./DIV. |
| Condition | Key is in ignition key cylinder |
| CHECK TRANSPONDER KEY ECU ASSEMBLY |
Disconnect the E15 ECU connector and measure the resistance and voltage between each terminal of the wire harness side connector.

| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND (E15-16) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| +B (E15-1) - GND (E15-16) | W - W-B | Battery | Always | 10 to 14 V |
| IG (E15-2) - GND (E15-16) | LG - W-B | Ignition switch signal | Ignition switch OFF | Below 1 V |
| Ignition switch ON | 10 to 14 V | |||
| KSW (E15-3) - GND (E15-16) | B - W-B | Unlock warning switch signal | No key is in ignition key cylinder | 10 kΩ or higher |
| Key is in ignition key cylinder | Below 1 Ω |
Reconnect the E15 ECU connector and measure the voltage of each terminal of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (E15-5) - Body ground | V - Body ground | Ground | Always | Below 1 Ω |
| KSW (E15-3) - GND (E15-16) | B - W-B | Unlock warning switch signal | No key is in ignition key cylinder | 10 to 14 V |
| Key is in ignition key cylinder | Below 1 V | |||
| VC5 (E15-14) - AGND (E15-5) | O - V | Power source | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | 4.6 to 5.4 V | |||
| TXCT (E15-4) - AGND (E15-5) | R - V | Transponder key amplifier communication signal | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | Waveform 1 | |||
| CODE (E15-15) - AGND (E15-5) | BR - V | Transponder key amplifier communication signal | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | Waveform 2 | |||
| EFIO (E15-13) - GND (E15-16) | L - W-B | ECM output signal | Ignition switch OFF | Below 1 V |
| Ignition switch ON | Waveform 3 | |||
| EFII (E15-12) - GND (E15-16) | G - W-B | ECM input signal | Ignition switch OFF | Below 1 V |
| Ignition switch ON | Waveform 4 | |||
| D (E15-9) - GND (E15-16) | GR - W-B | Diagnostic tester communication | Without communication | Below 1 V |
| During communication | Pules generation | |||
| CTY (E15-7) - GND (E15-16) | Y - W-B | Door courtesy signal | Switch pushed | 10 to 14 V |
| Switch free | Below 1 V | |||
| IND (E15-8) - GND (E15-16) | P - W-B | Security indicator signal | Security indicator light is on | 10 to 14 V |
| Security indicator light is off | Below 1 V |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Terminal | TXCT (E15-4) - AGND (E15-5) |
| Tool Setting | 2 V/DIV., 10 ms./DIV. |
| Condition | Key is in ignition key cylinder |
![]() |
Waveform 2 (Reference)
| Terminal | CODE (E15-15) - AGND (E15-5) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Key is in ignition key cylinder |
![]() |
Waveform 3 (Reference)
| Terminal | EFIO (E15-13) - GND (E15-16) |
| Tool Setting | 2 V/DIV., 1 s./DIV. |
| Condition | Ignition switch ON |
![]() |
Waveform 4 (Reference)
| Terminal | EFII (E15-12) - GND (E15-16) |
| Tool Setting | 2 V/DIV., 1 s./DIV. |
| Condition | Ignition switch ON |
| CHECK ECM |
Disconnect the C24*1 or C55*2 or C58*3 ECM connector and measure the resistance between the terminal of the wire harness side connector and body ground.

| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E1 (C24-104)*1 - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| E1 (C55-81)*2 - Body ground | ||||
| E1 (C58-81)*3 - Body ground |
Reconnect the C24*1 or C55*2 or C58*3 ECM connector. Measure the voltage between each terminal of the connector according to the value(s) in the table below.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IMI (A24-11)*1 - E1 (C24-104)*1
| Y - W-B | Transponder key ECU input signal | Ignition switch OFF | Below 1 V |
| IMI (A55-11)*2 - E1 (C55-81)*2
| Ignition switch ON | Waveform 1 | ||
| IMI (A24-11)*3 - E1 (C58-81)*3
| ||||
| IMO (A24-10)*1 - E1 (C24-104)*1
| G - W-B | Transponder key ECU output signal | Ignition switch OFF | Below 1 V |
| IMO (A55-10)*2 - E1 (C55-81)*2
| Ignition switch ON | Waveform 2 | ||
| IMO (A24-10)*3 - E1 (C58-81)*3
|
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Terminal | IMI (A24-11)*1 - E1 (C24-104)*1
|
| IMI (A55-11)*2 - E1 (C55-81)*2
| |
| IMI (A24-11)*3 - E1 (C58-81)*3
| |
| Tool Setting | 2 V/DIV., 1 s./DIV. |
| Condition | Ignition switch ON |
![]() |
Waveform 2 (Reference)
| Terminal | IMO (A24-10)*1 - E1 (C24-104)*1
|
| IMO (A55-10)*2 - E1 (C55-81)*2
| |
| IMO (A24-10)*3 - E1 (C58-81)*3
| |
| Tool Setting | 2 V/DIV., 1 s./DIV. |
| Condition | Ignition switch ON |