Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here



1. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY


  1. Install the conditioner unit assembly to the instrument panel reinforcement assembly with the 2 screws and 3 bolts.


    E128522E01

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    NOTICE:
    Tighten the bolts and screws in the order shown in the illustration to install the air conditioner unit assembly.



  1. Driver seat:



    1. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.


      E129156E04

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Passenger seat:

    1. Using a 12 mm hexagon wrench, adjust the position of the 2 collars.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }



  1. Install the instrument panel reinforcement assembly with the 2 bolts and nut.


    E128520

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } (NUT)

  1. Install the 2 bolts and 2 caps.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }

  1. Connect the connectors and clamps.



  1. Install the 6 nuts and 7 bolts.


    E128519



2. INSTALL STEERING COLUMN ASSEMBLY


    C133173E01
  1. Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the connectors and wire harness clamps to the steering column assembly.



    C132549E01
  1. Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.



    C132548E02
  1. Install the bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



    C133172
  1. Install the clamp to the steering column hole shield.



3. INSTALL NO. 1 AIR DUCT


    C132547
  1. Engage the 2 claws to install the No. 1 air duct.



4. INSTALL REAR NO. 1 AIR DUCT


    C129722
  1. Engage the 2 claws to install the rear No. 1 air duct.



5. INSTALL REAR NO. 2 AIR DUCT


    C129721
  1. Engage the 2 claws to install the rear No. 2 air duct.



6. INSTALL FLOOR CARPET BRACKET RH


7. INSTALL FLOOR CARPET BRACKET LH


8. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    C129716
  1. Install the No. 1 console box duct with the clip.



9. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Install the instrument panel safety pad assembly (Click here).



10. INSTALL HEATER INLET WATER HOSE


    E128511
  1. Install the water hose and attach the clip.



11. INSTALL HEATER OUTLET WATER HOSE
  1. Use the same procedures described for the heater inlet water hose.



12. INSTALL AIR CONDITIONING TUBE AND ACCESSORY
  1. Remove the attached vinyl tape from the tube.

  1. Sufficiently apply compressor oil to a new O-ring and fitting surface of the air conditioning tube assembly.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the air conditioning tube and accessory.

  1. Install the air conditioner tube and accessory.



13. INSTALL SUCTION HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the suction hose sub-assembly.



    E129157
  1. Move the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



14. INSTALL COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY


    C132714E01
  1. Install the cowl top outer front panel sub-assembly with the 4 nuts, the 4 bolts and the clamp.

    Torque:
    Nut:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }



15. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E128813E01
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration.



    E128812
  1. Connect the connector.



16. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E128811
  1. Engage the 4 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.



17. INSTALL FRONT FENDER TO COWL SIDE SEAL RH


    E128810
  1. Engage the claw and install the front fender to cowl side seal RH.



18. INSTALL FRONT FENDER TO COWL SIDE SEAL LH


    E128809
  1. Engage the claw and install the front fender to cowl side seal LH.



19. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



    E112237E01
  1. Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.



    E128820E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    37 to 52 mm (1.46 to 2.05 in.)



20. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



    E112237E01
  1. Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.



    E128821E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    23 to 38 mm (0.90 to 1.49 in.)

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.



21. CONNECT NEGATIVE BATTERY TERMINAL


22. INSPECT STEERING PAD


    C141754
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).



23. INSPECT SRS WARNING LIGHT
(Click here)


24. ADD ENGINE COOLANT (for 2AZ-FE)
  1. Close the radiator drain cock plug and 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    6.2 liters (6.6 US qts, 5.5 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



25. ADD ENGINE COOLANT (for 2GR-FE)
  1. Close the radiator drain cock plug and 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    9.0 liters (9.5 US qts, 7.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



26. CHECK FOR ENGINE COOLANT LEAKS


27. CHARGE WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.



  1. Charge with refrigerant HFC-134a (R134a).


    I037365E09

    Standard:
    450 to 550 g (15.9 to 19.4 oz.)

    SST
    07110-58060   (07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)

    NOTICE:
    1. Do not turn the A/C on before charging with refrigerant. Doing so will cause the cooler compressor to work without refrigerant, resulting in overheating of the cooler compressor.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear.
      The refrigerant amount should be checked by quantity, not with the sight glass.

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100 % of the refrigerant from an A/C system.



28. WARM UP ENGINE
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.



29. CHECK FOR REFRIGERANT LEAKS
  1. After recharging with refrigerant gas, check for leakage of refrigerant gas using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. IG OFF
    2. Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that there is some refrigerant remaining in the refrigeration system.
      When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)



    I042222E16
  1. Using a gas leak detector, check for leakage from the refrigerant lines.



    N014519E06
  1. Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.

    HINT:
    1. After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
    2. Bring the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
      If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow testing.

  1. If a gas leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.