BLOWER UNIT > INSTALLATION |
| 1. INSTALL BLOWER ASSEMBLY |
![]() |
Install the blower assembly with the 2 screws.
Connect the connector.
| 2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
Install the conditioner unit assembly to the instrument panel reinforcement assembly with the 2 screws and 3 bolts.

Driver seat:
Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.

Passenger seat:
Using a 12 mm hexagon wrench, adjust the position of the 2 collars.
Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.
Install the instrument panel reinforcement assembly with the 2 bolts and nut.

Install the 2 bolts and 2 caps.
Connect the connectors and clamps.
Install the 6 nuts and 7 bolts.

| 3. INSTALL STEERING COLUMN ASSEMBLY |
![]() |
Install the steering column assembly with the bolt and 2 nuts.
Connect the connectors and wire harness clamps to the steering column assembly.
![]() |
Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.
![]() |
Install the bolt.
![]() |
Install the clamp to the steering column hole shield.
| 4. INSTALL NO. 1 AIR DUCT |
![]() |
Engage the 2 claws to install the No. 1 air duct.
| 5. INSTALL REAR NO. 1 AIR DUCT |
![]() |
Engage the 2 claws to install the rear No. 1 air duct.
| 6. INSTALL REAR NO. 2 AIR DUCT |
![]() |
Engage the 2 claws to install the rear No. 2 air duct.
| 7. INSTALL FLOOR CARPET BRACKET RH |
| 8. INSTALL FLOOR CARPET BRACKET LH |
| 9. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct) |
![]() |
Install the No. 1 console box duct with the clip.
| 10. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
Install the instrument panel safety pad assembly (Click here).
| 11. INSTALL HEATER INLET WATER HOSE |
![]() |
Install the water hose and attach the clip.
| 12. INSTALL HEATER OUTLET WATER HOSE |
Use the same procedures described for the heater inlet water hose.
| 13. INSTALL AIR CONDITIONING TUBE AND ACCESSORY |
Remove the attached vinyl tape from the tube.
Sufficiently apply compressor oil to a new O-ring and fitting surface of the air conditioning tube assembly.
Install the O-ring on the air conditioning tube and accessory.
Install the air conditioner tube and accessory.
| 14. INSTALL SUCTION HOSE SUB-ASSEMBLY |
Remove the attached vinyl tape from the hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.
Install the O-ring on the suction hose sub-assembly.
![]() |
Move the hook connector in the direction indicated by the arrow in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 15. INSTALL COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY |
![]() |
Install the cowl top outer front panel sub-assembly with the 4 nuts, the 4 bolts and the clamp.
| 16. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Install the windshield wiper motor and link assembly with the 4 bolts.
![]() |
Connect the connector.
| 17. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Engage the 4 claws and install the cowl top ventilator louver sub-assembly.
Install the 2 clips.
| 18. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Engage the claw and install the front fender to cowl side seal RH.
| 19. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Engage the claw and install the front fender to cowl side seal LH.
| 20. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
Clean the wiper arm serrations.
When reinstalling:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 37 to 52 mm (1.46 to 2.05 in.) |
| 21. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
Clean the wiper arm serrations.
When reinstalling:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 23 to 38 mm (0.90 to 1.49 in.) |
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 22. CONNECT NEGATIVE BATTERY TERMINAL |
| 23. INSPECT STEERING PAD |
![]() |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Make sure that the horn sounds.
| 24. INSPECT SRS WARNING LIGHT |
| 25. ADD ENGINE COOLANT (for 2AZ-FE) |
Close the radiator drain cock plug and 2 cylinder block drain cock plugs.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reservoir tank cap.
Start the engine, and warm it up.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 26. ADD ENGINE COOLANT (for 2GR-FE) |
Close the radiator drain cock plug and 2 cylinder block drain cock plugs.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reservoir tank cap.
Start the engine, and warm it up.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 27. CHECK FOR ENGINE COOLANT LEAKS |
| 28. CHARGE WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump.
Charge with refrigerant HFC-134a (R134a).

| 29. WARM UP ENGINE |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 30. CHECK FOR REFRIGERANT LEAKS |
After recharging with refrigerant gas, check for leakage of refrigerant gas using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a gas leak detector, check for leakage from the refrigerant lines.
![]() |
Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.
If a gas leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.