PLASMACLUSTER > REMOVAL |
| 1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 2. DISCONNECT BATTERY NEGATIVE TERMINAL |
| 3. REMOVE LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.
| 4. REMOVE LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.
| 5. REMOVE STEERING PAD |
![]() |
Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.
![]() |
Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.
Disconnect the horn connector from the steering pad.
Disconnect the 2 airbag connectors and remove the steering pad.
Remove the steering pad.
| 6. REMOVE STEERING WHEEL ASSEMBLY |
Remove the steering wheel assembly set nut.
Put matchmarks on the steering wheel assembly and the steering main shaft.
Disconnect the connectors from the spiral cable.
![]() |
Using SST, remove the steering wheel assembly.
| 7. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower instrument panel finish panel LH.
| 10. REMOVE STEERING COLUMN COVER |
![]() |
Remove the 2 screws <D>.
Disengage the 2 claws and remove the lower steering column cover.
Disengage the claw and remove the upper steering column cover.
| 11. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.
![]() |
Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.
| 12. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Disengage the 3 claws and the 2 clips.
Disconnect each connector and remove the instrument panel sub-assembly.
| 13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL |
![]() |
Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
| 14. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
Remove the 2 clips.
Disengage the guide and 4 claws and then remove the instrument cluster finish panel.
| 15. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws <E>.
Disconnect each connector and remove the combination meter assembly.
| 16. REMOVE FRONT DOOR SCUFF PLATE RH |
| 17. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 18. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides and remove the No. 2 under cover sub-assembly.
| 19. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Remove the bolt <A>.
![]() |
Remove the 4 screws <B>.
Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.
| 20. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 21. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 22. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
| 23. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
| 24. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Disengage the 6 claws and the 3 clips, and then remove the floor shift position indicator housing sub-assembly.
with Seat Heater System:
Disconnect each connector.
| 25. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle) |
![]() |
Open the lid of the upper console panel.
Apply protective tape to the area shown in the illustration.
![]() |
Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.
| 26. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Disengage the 3 claws and the 5 clips.
Disengage the clamp.
Disconnect the connector and remove the upper console rear panel sub-assembly.
| 27. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.
| 28. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY |
![]() |
Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.
| 29. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY |
![]() |
Apply protective tape to the areas shown in the illustration.
![]() |
Using a moulding remover, disengage the 3 clips.
![]() |
Using a moulding remover, disengage the 4 clips.
Disconnect the connector and remove the instrument panel No. 2 register assembly.
| 30. REMOVE RADIO TUNER OPENING COVER WITH HEATER CONTROL PANEL ASSEMBLY (w/o Radio Receiver) |
![]() |
Remove the 4 bolts <N>.
Disengage the 6 clips and remove the radio tuner opening cover with heater control panel assembly.
Disconnect the connector.
| 31. REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Radio Receiver) |
![]() |
Remove the 4 bolts.
Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the radio receiver with heater control panel assembly.
| 32. REMOVE CONSOLE BOX POCKET |
Remove the console box pocket.
| 33. REMOVE CONSOLE BOX CARPET |
![]() |
Remove the console box carpet.
| 34. REMOVE CONSOLE BOX ASSEMBLY |
![]() |
Remove the 2 screws <F>.
![]() |
Remove the 2 bolts <G> and the console box assembly.
| 35. REMOVE NO. 2 CONSOLE BOX INSERT FRONT |
![]() |
Remove the 3 screws <F>.
Disengage the clip and remove the No. 2 console box insert front.
| 36. REMOVE NO. 1 CONSOLE BOX INSERT FRONT |
![]() |
Remove the 3 screws <F>.
Disengage the clip and remove the No. 1 console box insert front.
| 37. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish LH.
Remove the clip <A> from the vehicle body.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 38. REMOVE INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY |
![]() |
Disengage the 4 clips and remove the instrument panel No. 1 register assembly.
| 39. REMOVE INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Disengage the 6 claws and the 2 clips.
Disengage the 2 guides and remove the instrument panel No. 1 speaker panel sub-assembly.
| 40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) |
![]() |
Remove the 2 bolts and front No. 2 speaker assembly.
Disconnect the connector.
| 41. REMOVE FRONT PILLAR GARNISH RH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish RH.
Remove the clip <A> from the vehicle body.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 42. REMOVE INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY |
![]() |
Disengage the 4 clips and remove the instrument panel No. 3 register assembly.
| 43. REMOVE INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Disengage the 6 claws and the 2 clips.
Disengage the 2 guides and remove the instrument panel No. 2 speaker panel sub-assembly.
| 44. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side) |
| 45. REMOVE NO. 1 DEFROSTER NOZZLE GARNISH |
![]() |
Disengage the 8 clips and the 4 guides.
Disconnect each connector and remove the No. 1 defroster nozzle garnish.
| 46. REMOVE INSTRUMENT PANEL WIRE ASSEMBLY |
![]() |
Disconnect the connector (yellow colored one).
| 47. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
Disengage each clamp.
Disconnect each connector.
Remove the bolt <J>.
Remove the 2 passenger airbag bolts <K>.
with Plasmacluster:
Disconnect the connector.

Remove the 2 bolts <H> or <O>.
Remove the 2 nuts <C> or <I>.
Disengage the 5 claws and remove the instrument panel safety pad assembly.

| 48. REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT |
![]() |
Remove the screw <F> and the side No. 1 defroster nozzle duct.
| 49. REMOVE NO. 1 HEATER TO REGISTER DUCT |
![]() |
Remove the 3 screws <F> and the No. 1 heater to register duct.
| 50. REMOVE PLASMACLUSTER |
![]() |
Remove the 2 screws and Plasmacluster.