Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

AUTO, OFF, TEMP UP (+), and TEMP DOWN (-) switches are located on the steering pad switch. The resistance of the steering pad switch changes in accordance with switch operation. The A/C control assembly (heater control base sub-assembly) outputs voltage to the steering pad switch and reads voltage changes due to the resistance changes that result from switch operation.

HINT:
If there is an open in the circuit, the A/C system cannot be operated by the steering pad switch assembly.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the A/C control assembly (heater control base sub-assembly) cannot be operated by the steering pad switch assembly, and the A/C control assembly (heater control base sub-assembly) will not be able to function correctly.


WIRING DIAGRAM


E208296E03


INSPECTION PROCEDURE

1.INSPECT A/C CONTROL ASSEMBLY


    E124479E02
  1. Remove the A/C control assembly (heater control base sub-assembly) with the connectors still connected.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    F16-9 (ADI1) - F16-8 (SG)
    AUTO switch: ON
    Below 2.5 Ω
    F16-9 (ADI1) - F16-8 (SG)
    OFF switch: ON
    Approx. 329 Ω
    F16-9 (ADI1) - F16-8 (SG)
    TEMP+ switch: ON
    Approx. 1,000 Ω
    F16-9 (ADI1) - F16-8 (SG)
    TEMP- switch: ON
    Approx. 3,110 Ω



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly.



  1. Disconnect the connector from the steering pad switch assembly.


    E124484E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection (Symbols)
    Condition
    Specified Condition
    a1-3 (AC1) - a1-2 (EAC)
    AUTO switch: ON
    Below 2.5 Ω
    a1-3 (AC1) - a1-2 (EAC)
    OFF switch: ON
    Approx. 329 Ω
    a1-3 (AC1) - a1-2 (EAC)
    TEMP+ switch: ON
    Approx. 1,000 Ω
    a1-3 (AC1) - a1-2 (EAC)
    TEMP- switch: ON
    Approx. 3,110 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


3.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    I039337E26
  1. Disconnect the connector from the spiral cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection (Symbols)
Condition
Specified Condition
E18-10 (AC1) - a1-3 (AC1)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
E18-9 (EAC) - a1-2 (EAC)
Center
Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right

HINT:
The spiral cable makes a maximum of approximately 5 rotations.



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (A/C CONTROL ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)


    E124480E04
  1. Disconnect the connector from the A/C control assembly (heater control base sub-assembly).



    I046136E06
  1. Disconnect the connector from the spiral cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F16-9 (ADI1) - E18-10 (AC1)
    Always
    Below 1 Ω
    F16-8 (SG) - E18-9 (EAC)
    Always
    Below 1 Ω
    F16-9 (ADI1) - E18-10 (AC1)
    Always
    10 kΩ or higher
    F16-8 (SG) - E18-9 (EAC)
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEATER CONTROL BASE SUB-ASSEMBLY