RADIATOR > REMOVAL |
| 1. DRAIN ENGINE COOLANT |
| 2. REMOVE ENGINE UNDER COVER RH |
| 3. REMOVE ENGINE UNDER COVER LH |
| 4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the mass air flow meter connector (*1).
Disconnect the purge VSV connector (*2).
Disconnect the 2 purge VSV vacuum hoses (*3).
Disconnect the purge line hose from the clamp (*4).
![]() |
Disconnect the No. 2 ventilation hose from the air cleaner hose.
![]() |
Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.
![]() |
Remove the 2 bolts and air cleaner cap.
Remove the air cleaner filter element from the air cleaner case.
| 5. REMOVE AIR CLEANER INLET ASSEMBLY |
![]() |
Remove the 2 bolts, clamp and air cleaner inlet.
| 6. REMOVE FRONT BUMPER ASSEMBLY (w/o Headlight Cleaner System) |
![]() |
Put protective tape around the front bumper assembly.
![]() |
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
![]() |
Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
![]() |
Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
Disconnect each connector, and then remove the front bumper assembly.
| 7. REMOVE FRONT BUMPER ASSEMBLY (w/ Headlight Cleaner System) |
![]() |
Put protective tape around the front bumper assembly.
![]() |
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
![]() |
Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
![]() |
Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
Disconnect each connector.
![]() |
Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.
| 8. REMOVE FRONT BUMPER ENERGY ABSORBER |
![]() |
Remove the front bumper energy absorber from the front bumper reinforcement sub-assembly.
| 9. SEPARATE RADIATOR RESERVE TANK HOSE |
![]() |
Separate the radiator reserve tank hose from the radiator assembly.
| 10. DISCONNECT RADIATOR HOSE INLET |
![]() |
Disconnect the radiator hose inlet from the radiator assembly.
| 11. DISCONNECT RADIATOR HOSE OUTLET |
![]() |
Disconnect the radiator hose outlet from the radiator assembly.
| 12. DISCONNECT OIL COOLER INLET HOSE (for Automatic Transaxle) |
![]() |
Disconnect the oil cooler inlet hose from the radiator assembly.
| 13. DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle) |
![]() |
Disconnect the oil cooler outlet hose from the radiator assembly.
| 14. REMOVE RADIATOR SUPPORT UPPER |
![]() |
Disconnect the horn connector.
Remove the 3 bolts and separate the hood lock assembly from the radiator support upper.
For LHD:
![]() |
Remove the clamp and separate the hood lock control cable from the radiator support upper.
For RHD:
![]() |
Remove the clamp and separate the hood rock control cable from the radiator support upper.
![]() |
Remove the 5 bolts and radiator support upper.
| 15. REMOVE RADIATOR ASSEMBLY |
![]() |
Remove the 3 clamps and 2 connectors.
![]() |
Remove the 4 bolts and separate the condenser assembly from the radiator assembly.
![]() |
Remove the radiator assembly from the body.
| 16. REMOVE FAN ASSEMBLY WITH MOTOR |
![]() |
Release the 3 snap fits and lift the fan assembly with motor from the radiator.
| 17. REMOVE RADIATOR SUPPORT CUSHION |
![]() |
Remove the 2 radiator support cushions from the radiator assembly.
| 18. REMOVE RADIATOR SUPPORT LOWER |
![]() |
Remove the 2 radiator support lowers from the radiator assembly.