RADIATOR > REMOVAL |
| 1. REMOVE ENGINE UNDER COVER RH |
| 2. REMOVE ENGINE UNDER COVER LH |
| 3. DRAIN ENGINE COOLANT |
Remove the radiator cap sub-assembly from the radiator assembly.
Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.

| 4. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.
| 5. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 7 clips and intake duct seal.
| 6. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the 3 vacuum hoses.
![]() |
Disconnect the mass air flow meter connector (*1).
Disconnect the No. 2 ventilation hose (*2).
Disconnect the hose band (*3).
![]() |
Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.
| 7. REMOVE AIR CLEANER INLET SUB-ASSEMBLY |
![]() |
Remove the 2 bolts, clamp and air cleaner inlet.
| 8. REMOVE NO. 1 AIR CLEANER INLET |
![]() |
Remove the bolt and No. 1 air cleaner inlet.
| 9. REMOVE FRONT BUMPER ASSEMBLY (w/o Headlight Cleaner System) |
![]() |
Put protective tape around the front bumper assembly.
![]() |
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
![]() |
Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
![]() |
Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
Disconnect each connector, and then remove the front bumper assembly.
| 10. REMOVE FRONT BUMPER ASSEMBLY (w/ Headlight Cleaner System) |
![]() |
Put protective tape around the front bumper assembly.
![]() |
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
![]() |
Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
![]() |
Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
Disconnect each connector.
![]() |
Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.
| 11. REMOVE FRONT BUMPER ENERGY ABSORBER |
![]() |
Remove the front bumper energy absorber from the front bumper reinforcement sub-assembly.
| 12. SEPARATE RADIATOR RESERVE TANK HOSE |
![]() |
Separate the radiator reserve tank hose from the radiator assembly.
| 13. DISCONNECT RADIATOR HOSE INLET |
![]() |
Separate the radiator inlet hose from the radiator assembly.
| 14. DISCONNECT RADIATOR HOSE OUTLET |
![]() |
Separate the radiator outlet hose from the radiator assembly.
| 15. DISCONNECT NO. 1 OIL COOLER INLET HOSE |
![]() |
Separate the No. 1 oil cooler inlet hose from the radiator assembly.
| 16. DISCONNECT NO. 1 OIL COOLER OUTLET HOSE |
![]() |
Separate the No. 1 oil cooler outlet hose from the radiator assembly.
| 17. REMOVE RADIATOR SUPPORT UPPER |
Disconnect the horn connector.
![]() |
Remove the 3 bolts and separate the hood lock assembly from the radiator support upper.
![]() |
For LHD:
Remove the clamp and separate the hood lock control cable from the radiator support upper.
![]() |
For RHD:
Remove the clamp and separate the hood lock control cable from the radiator support upper.
![]() |
Remove the 5 bolts and radiator support upper.
| 18. REMOVE FAN SHROUD |
![]() |
Remove the 3 clamps and connector.
![]() |
Release the 3 snap fits and lift the fan assembly with motor from the radiator.
| 19. REMOVE RADIATOR ASSEMBLY |
![]() |
Remove the 4 bolts and separate the condenser assembly from the radiator assembly.
![]() |
Remove the radiator assembly from the body.
| 20. REMOVE RADIATOR SUPPORT CUSHION |
![]() |
Remove the 2 radiator support cushions from the radiator assembly.
| 21. REMOVE RADIATOR SUPPORT LOWER |
![]() |
Remove the 2 radiator support lowers from the radiator assembly.