Home › ENGINE ยท 2AZ-FE › COOLING › RADIATOR

RADIATOR > REMOVAL

for Preparation Click here



1. DRAIN ENGINE COOLANT


2. REMOVE ENGINE UNDER COVER RH


3. REMOVE ENGINE UNDER COVER LH


4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A135666E01
  1. Disconnect the mass air flow meter connector (*1).

  1. Disconnect the purge VSV connector (*2).

  1. Disconnect the 2 purge VSV vacuum hoses (*3).

  1. Disconnect the purge line hose from the clamp (*4).



    A135667E01
  1. Disconnect the No. 2 ventilation hose from the air cleaner hose.



    A135668
  1. Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.



    A135669
  1. Remove the 2 bolts and air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.



5. REMOVE AIR CLEANER INLET ASSEMBLY


    A134903
  1. Remove the 2 bolts, clamp and air cleaner inlet.



6. REMOVE FRONT BUMPER ASSEMBLY (w/o Headlight Cleaner System)


    B140159E01
  1. Put protective tape around the front bumper assembly.



    B138884E01
  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.



    B137735
  1. Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.



    B137736
  1. Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect 2 fog light connectors.

  1. w/ TOYOTA Parking Assist-sensor System:

    1. Disengage the clamp and disconnect the clearance sonar connector.

  1. Remove the front bumper assembly.



7. REMOVE FRONT BUMPER ASSEMBLY (w/ Headlight Cleaner System)


    B137734E01
  1. Put protective tape around the front bumper assembly.



    B138884E01
  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.



    B140161
  1. Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.



    B140160
  1. Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect 2 fog light connectors.

  1. w/ TOYOTA Parking Assist-sensor System:

    1. Disengage the clamp and disconnect the clearance sonar connector.



    B137737
  1. Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.



8. REMOVE FRONT BUMPER ENERGY ABSORBER


    B137728
  1. Remove the front bumper energy absorber from the front bumper reinforcement sub-assembly.



9. SEPARATE RADIATOR RESERVE TANK HOSE


    A135233
  1. Separate the radiator reserve tank hose from the radiator assembly.



10. DISCONNECT RADIATOR HOSE INLET


    A135240
  1. Disconnect the radiator hose inlet from the radiator assembly.



11. DISCONNECT RADIATOR HOSE OUTLET


    A133364
  1. Disconnect the radiator hose outlet from the radiator assembly.



12. DISCONNECT OIL COOLER INLET HOSE (for Automatic Transaxle)


    A133365
  1. Disconnect the oil cooler inlet hose from the radiator assembly.



13. DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle)


    A133366
  1. Disconnect the oil cooler outlet hose from the radiator assembly.



14. REMOVE RADIATOR SUPPORT UPPER


    A135235
  1. Disconnect the horn connector.

  1. Remove the 3 bolts and separate the hood lock assembly from the radiator support upper.



  1. For LHD:



      A135236
    1. Remove the clamp and separate the hood lock control cable from the radiator support upper.



  1. For RHD:



      A139356
    1. Remove the clamp and separate the hood rock control cable from the radiator support upper.



    A135237
  1. Remove the 5 bolts and radiator support upper.



15. REMOVE RADIATOR ASSEMBLY


    A135241
  1. Remove the 3 clamps and 2 connectors.



    A135239
  1. Remove the 4 bolts and separate the condenser assembly from the radiator assembly.



    A135238
  1. Remove the radiator assembly from the body.



16. REMOVE FAN ASSEMBLY WITH MOTOR


    A143820E01
  1. Release the 3 snap fits and lift the fan assembly with motor from the radiator.



17. REMOVE RADIATOR SUPPORT CUSHION


    A133371E02
  1. Remove the 2 radiator support cushions from the radiator assembly.



18. REMOVE RADIATOR SUPPORT LOWER


    A133371E03
  1. Remove the 2 radiator support lowers from the radiator assembly.