OIL PUMP > INSTALLATION |
| 1. INSTALL TIMING CHAIN CASE OIL SEAL |
![]() |
Using SST, tap in a new oil seal until its surface is flush with the timing chain case edge.
| 2. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY |
Apply seal packing in a continuous line to the engine unit as shown in the following illustration.

Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

| Area | Seal Packing Diameter | Application Position from Inside Seal Line |
| Continuous Line Area | 4.5 mm or more (0.177 in.) | 3.0 to 4.0 mm (0.118 to 0.158 in.) |
| Alternate Long and short Dashed Line Area | 3.5 mm or more (0.138 in.) | 2.0 to 3.0 mm (0.079 to 0.118 in.) |
| Dashed Line Area | 3.5 mm or more (0.138 in.) | 3.0 to 4.0 mm (0.118 to 0.158 in.) |
| Diagonal Line Area | 6.0 mm or more (0.236 in.) | 5.0 mm (0.197 in.) |
![]() |
Install a new gasket.
![]() |
Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.

| Item | Length |
| Bolt A | 40 mm (1.57 in.) |
| Bolt B | 55 mm (2.17 in.) |
| Bolt C | 25 mm (0.98 in.) |
Fully tighten the bolts in this order: Area 1 and Area 2.
Fully tighten the bolts and nuts in this order: Area 3.
Fully tighten the bolts in this order: Area 4.
| 3. INSTALL WATER INLET HOUSING |
![]() |
Install 2 new O-rings.
![]() |
Install the stud bolts.
![]() |
Install the water inlet with the 2 bolts and nut.
Connect the water by-pass hose No. 1.
Apply adhesive around the drain cock.
Install the housing drain cock to the water inlet housing.
Install the housing plug to the water drain cock.
Install a new gasket to the thermostat.
![]() |
Align the thermostat jiggle valve with the upper stud bolt, and insert the thermostat in the water inlet housing.
![]() |
Install the water inlet with the 2 nuts.
| 4. INSTALL NO. 1 ENGINE MOUNTING BRACKET FRONT LH |
![]() |
Install the engine mounting bracket with the 6 bolts.
When replacing a stud bolt, install it by using an E8 "torx" socket wrench.
| 5. INSTALL OIL PAN SUB-ASSEMBLY |
When replacing a stud bolt, install it by using an E8 "torx" socket wrench.

![]() |
Install 2 new O-rings.
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Install the oil pan with the 16 bolts and 2 nuts.
| 6. INSTALL OIL STRAINER SUB-ASSEMBLY |
![]() |
Using an E6 "torx" socket, install the stud bolts as shown in the illustration.
![]() |
Install a new gasket and the oil strainer with the bolt and 2 nuts.
| 7. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Using an E6 "torx" socket, install the stud bolts as shown in the illustration.
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Install the oil pan with the 16 bolts and 2 nuts.
| 8. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1) |
![]() |
Apply seal packing as shown in the illustration.
![]() |
Install 3 new gaskets as shown in the illustration.
Install a new gasket to the head cover.
![]() |
Install a head cover with the 12 bolts and a new washer.
| 9. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2) |
![]() |
Apply seal packing as shown in the illustration.
![]() |
Install 3 new gaskets as shown in the illustration.
Install a new gasket to the head cover.
![]() |
Install the head cover with the 12 bolts and a new washer.
| 10. INSTALL CRANKSHAFT PULLEY |
Align the pulley set key with the key groove of the pulley, and slide on the pulley.
![]() |
Using SST, install the pulley bolt.
| 11. INSTALL NO. 1 OIL PIPE |
Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.
![]() |
Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).
Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil check valve bolt.
Tighten the oil pipe union (on the head cover side).
Tighten the oil pipe union (on the cylinder head side).
| 12. INSTALL OIL PIPE |
Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.
![]() |
Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).
Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil check valve bolt.
Install the bolt (A) to the cylinder head.
Tighten the oil pipe union (on the head cover side).
Tighten the oil pipe union (on the cylinder head side).
| 13. INSTALL NO. 1 VACUUM SWITCHING VALVE |
![]() |
Install the bolt and No. 1 vacuum switching valve.
| 14. INSTALL RADIO SETTING CONDENSER |
![]() |
Install the 2 bolts and 2 radio setting condensers.
| 15. INSTALL WATER PUMP PULLEY |
![]() |
Temporarily install the water pump pulley with the 4 bolts.
Using SST, hold the water pump pulley.
Tighten the 4 bolts.
| 16. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Install the No. 2 idler pulley sub-assembly and 2 plates with the bolt.
| 17. INSTALL NO. 2 TIMING GEAR COVER |
![]() |
Install the No. 2 timing gear cover with the 2 bolts.
| 18. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Temporarily install the V-ribbed belt tensioner with the 5 bolts.
Install the V-ribbed belt tensioner by tightening the bolt 1 and bolt 2 in the order shown in the illustration.
Tighten the other bolts.
| 19. INSTALL ENGINE MOUNTING BRACKET RH |
![]() |
Install the engine mounting bracket RH with the 3 bolts.
| 20. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Install a new gasket as shown in the illustration.
![]() |
Install the exhaust manifold sub-assembly LH with the 6 nuts.
| 21. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the No. 2 insulator with the 3 bolts.
| 22. INSTALL NO. 2 MANIFOLD STAY |
![]() |
Install the No. 2 manifold stay with the bolt and nut.
| 23. INSTALL OIL LEVEL GAUGE GUIDE SUB-ASSEMBLY |
![]() |
Install 2 new O-rings to the oil level gauge guide.
Apply a light coat of engine oil to the O-rings.
Push in the oil level gauge guide end into the guide hole.
Install the oil level gauge guide No. 1 with the bolt.
Install the oil level gauge guide No. 2 with the bolt.
Install the oil level gauge.
| 24. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Install a new gasket as shown in the illustration.
![]() |
Install the exhaust manifold sub-assembly RH with the 6 nuts.
| 25. INSTALL NO. 2 ENGINE MOUNTING STAY RH |
Install the No. 2 mounting stay RH with the bolt.
| 26. INSTALL IGNITION COIL ASSEMBLY |
Install the 6 ignition coil assemblies with the 6 bolts.
| 27. INSTALL INTAKE AIR SURGE TANK ASSEMBLY |
| Components | ||
| Surge Tank and Intake Manifold | ||
| No. 1 Surge Tank Stay and Cylinder Head Cover | ||
| No. 1 Surge Tank Stay and Surge Tank | ||
| Throttle Body Bracket and Cylinder Head Cover | ||
| Throttle Body Bracket and Surge Tank |
Install a new gasket to the intake air surge tank.
![]() |
Using a 5 mm hexagon socket wrench, install the 4 bolts and 2 nuts.
Install the throttle body bracket, No. 1 surge tank stay and 4 bolts.
![]() |
Connect the connector.
![]() |
Install the vacuum hose clamp with the bolt.
Connect the No. 1 ventilation hose.
![]() |
Install the clamp and connect the throttle body assembly connector (*3).
Connect the vapor feed hose (*2).
Connect the 2 water by-pass hoses to the throttle body assembly (*1).
| 28. REMOVE ENGINE STAND |
| 29. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
![]() |
Apply adhesive to 2 or 3 threads of the mounting bolt end.
![]() |
Install the front spacer, drive plate and rear spacer on the crankshaft.
Install and tighten the 8 mounting bolts uniformly in several steps.
| 30. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY |
| 31. INSTALL STARTER ASSEMBLY |
![]() |
Install the starter assembly with the 2 bolts.
Connect the wire harness to terminal 30 and install the nut. Then, attach the terminal cap.
Connect the terminal 50 connector to the starter assembly.
| 32. INSTALL ENGINE WIRE |
| 33. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Coat the spline of the inboard joint shaft assembly with ATF.
Align the shaft splines and install the drive shaft assembly LH with a brass bar and hammer.
| 34. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
![]() |
Coat the spline of the inboard joint shaft assembly with ATF.
Install the front drive shaft the assembly RH.
Using a screwdriver, install a new bearing bracket hole snap ring.
Install a new bolt.
| 35. INSTALL FRONT FRAME ASSEMBLY |
![]() |
Install the engine mounting insulators RH and LH with the 2 nuts.
![]() |
Install the engine mounting insulator FR with the bolt.
![]() |
Connect the connector and clamp.
![]() |
Connect the 2 clamps.
| 36. INSTALL VANE PUMP ASSEMBLY |
![]() |
Install the vane pump with the 2 bolts.
Install the pressure feed tube clamp bolt.
Connect the power steering oil pressure switch connector.
| 37. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |