Home › ENGINE ยท 2GR-FE › LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
(Click here)


2. SECURE ENGINE



3. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    A129464E01
  1. Disconnect the 2 water by-pass hoses from the throttle with motor body assembly.

  1. Disconnect the vapor feed hose.

  1. Disconnect the throttle with motor body assembly connector and clamp.

  1. Disconnect the No. 1 ventilation hose.



    A129466
  1. Remove the bolt and vacuum hose clamp.



    A129467
  1. Disconnect the connector.

  1. Remove the 4 bolts, No. 1 surge tank stay and throttle body bracket.



    A139209E01
  1. Using a 5 mm socket hexagon wrench, remove the 4 bolts.

  1. Remove the 2 nuts and intake air surge tank.

  1. Remove the gasket from the intake air surge tank.



4. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 6 bolts and 6 ignition coils.



5. REMOVE NO. 2 ENGINE MOUNTING STAY RH
  1. Remove the bolt and No. 2 engine mounting stay RH.



6. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Disconnect the A/F sensor connector clamp.



    A129637
  1. Uniformly loosen and remove the 6 nuts.

  1. Remove the manifold and gasket.



7. REMOVE OIL LEVEL GAUGE GUIDE SUB-ASSEMBLY


    A129638
  1. Remove the oil level gauge.

  1. Remove the 2 bolts, oil level gauge guides No. 1 and No. 2.

  1. Remove the O-rings from the oil level gauge guide.



8. REMOVE NO. 2 MANIFOLD STAY


    A129639
  1. Remove the 2 bolts and No. 2 manifold stay.



9. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A129640
  1. Remove the 3 bolts and No. 2 insulator.



10. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A129641
  1. Uniformly loosen and remove the 6 nuts.

  1. Remove the manifold and gasket.



11. REMOVE ENGINE MOUNTING BRACKET RH


    A129642
  1. Remove the 3 bolts and engine mounting bracket RH.



12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A129644
  1. Remove the 5 bolts and V-ribbed belt tensioner assembly.



13. REMOVE NO. 2 TIMING GEAR COVER


    A132987
  1. Remove the 2 bolts and No. 2 timing gear cover.



14. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A129645E01
  1. Remove the bolt, plate and No. 2 idler pulley sub-assembly.



15. REMOVE WATER PUMP PULLEY


    A128112E03
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 4 bolts and water pump pulley.



16. REMOVE RADIO SETTING CONDENSER


    A132991
  1. Remove the 2 bolts and 2 radio setting condensers.



17. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY


    A132992
  1. Remove the bolt and No. 1 vacuum switching valve.



18. REMOVE NO. 1 OIL PIPE


    A135726E01
  1. Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter LH and gaskets.



19. REMOVE OIL PIPE


    A134878E01
  1. Remove the bolt.

  1. Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter RH and gaskets.



20. REMOVE CRANKSHAFT PULLEY


    A120690E02
  1. Using SST, loosen the crankshaft pulley bolt.

    SST
    09213-70011   (09213-70020)
    09330-00021  



    A120691E02
  1. Using SST, remove the crankshaft pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



21. REMOVE NO. 1 ENGINE MOUNTING BRACKET FRONT LH


    A129672
  1. Remove the 6 bolts and engine mounting bracket.

  1. Using "Torx" socket wrench E8, remove the 2 stud bolts.



22. REMOVE WATER INLET HOUSING


    A129673
  1. Remove the 2 nuts, water inlet and thermostat.

  1. Remove the gasket.

  1. Remove the housing plug.

  1. Remove the housing drain cock.

  1. Remove the 2 stud bolts.

  1. Separate the water by-pass hose No. 1.



    A134879E01
  1. Remove the 2 bolts, nut, and water inlet housing.



    A129675
  1. Remove the 2 O-rings.



23. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)


    A129679
  1. Remove the 12 bolts, seal washer, head cover and gasket.



    A129699
  1. Remove the 3 gaskets.



24. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)


    A129678E02
  1. Remove the 12 bolts, seal washer, head cover and gasket.

    NOTICE:
    The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the head cover.



    A129705
  1. Remove the 3 gaskets.



25. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A129680E01
  1. Remove the 16 bolts and 2 nuts.



    A120816E01
  1. Insert the blade of SST between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

    SST
    09032-00100  

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.

  1. Using "Torx" socket wrench E6, remove the 2 stud bolts.



26. REMOVE OIL STRAINER SUB-ASSEMBLY


    A129681
  1. Remove the bolt, 2 nuts, oil strainer and gasket.

  1. Using "Torx" socket wrench E6, remove the 2 stud bolts.



27. REMOVE OIL PAN SUB-ASSEMBLY


    A129682E02
  1. Remove the 16 bolts and 2 nuts.

    HINT:
    Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.



    A129683E01
  1. Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.



    A129684
  1. Remove the 2 O-rings.

  1. Using "Torx" socket wrench E8, remove the 2 stud bolts.



28. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A128004
  1. Remove the 23 bolts and 2 nuts as shown in the illustration.



    A129690E02
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.

    HINT:
    Tape the screwdriver tip before use.



    A128006E01
  1. Remove the gasket.



29. REMOVE TIMING CHAIN CASE OIL SEAL


    A128007E01
  1. Using a screwdriver, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.