OIL PUMP > REMOVAL |
| 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE |
| 2. SECURE ENGINE |
| 3. REMOVE INTAKE AIR SURGE TANK ASSEMBLY |
![]() |
Disconnect the 2 water by-pass hoses from the throttle body assembly (*1).
Disconnect the vapor feed hose (*2).
Disconnect the throttle body assembly connector and clamp (*3).
Disconnect the No. 1 ventilation hose.
![]() |
Remove the bolt and vacuum hose clamp.
![]() |
Disconnect the connector.
Remove the 4 bolts, No. 1 surge tank stay and throttle body bracket.
![]() |
Using a 5 mm socket hexagon wrench, remove the 4 bolts (*4).
Remove the 2 nuts and intake air surge tank (*5).
Remove the gasket from the intake air surge tank.
| 4. REMOVE IGNITION COIL ASSEMBLY |
Remove the 6 bolts and 6 ignition coils.
| 5. REMOVE NO. 2 ENGINE MOUNTING STAY RH |
Remove the bolt and No. 2 engine mounting stay RH.
| 6. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH |
Disconnect the A/F sensor connector clamp.
![]() |
Uniformly loosen and remove the 6 nuts.
Remove the manifold and gasket.
| 7. REMOVE OIL LEVEL GAUGE GUIDE SUB-ASSEMBLY |
![]() |
Remove the oil level gauge.
Remove the 2 bolts, oil level gauge guides No. 1 and No. 2.
Remove the O-rings from the oil level gauge guide.
| 8. REMOVE NO. 2 MANIFOLD STAY |
![]() |
Remove the bolt, nut and No. 2 manifold stay.
| 9. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 3 bolts and No. 2 insulator.
| 10. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Uniformly loosen and remove the 6 nuts.
Remove the manifold and gasket.
| 11. REMOVE ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 3 bolts and engine mounting bracket RH.
| 12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 5 bolts and V-ribbed belt tensioner assembly.
| 13. REMOVE NO. 2 TIMING GEAR COVER |
![]() |
Remove the 2 bolts and No. 2 timing gear cover.
| 14. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt, 2 plates and No. 2 idler pulley sub-assembly.
| 15. REMOVE WATER PUMP PULLEY |
![]() |
Using SST, hold the water pump pulley.
Remove the 4 bolts and water pump pulley.
| 16. REMOVE RADIO SETTING CONDENSER |
![]() |
Remove the 2 bolts and 2 radio setting condensers.
| 17. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY |
![]() |
Remove the bolt and No. 1 vacuum switching valve.
| 18. REMOVE NO. 1 OIL PIPE |
![]() |
Remove the 2 oil pipe unions and oil pipe.
Remove the oil control valve filter LH and gaskets.
| 19. REMOVE OIL PIPE |
![]() |
Remove the bolt.
Remove the 2 oil pipe unions and oil pipe.
Remove the oil control valve filter RH and gaskets.
| 20. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, loosen the crankshaft pulley bolt.
![]() |
Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
| 21. REMOVE NO. 1 ENGINE MOUNTING BRACKET FRONT LH |
![]() |
Remove the 6 bolts and engine mounting bracket.
Using "Torx" socket wrench E8, remove the 2 stud bolts.
| 22. REMOVE WATER INLET HOUSING |
![]() |
Remove the 2 nuts, water inlet and thermostat.
Remove the gasket.
Remove the housing plug.
Remove the housing drain cock.
Remove the 2 stud bolts.
Separate the water by-pass hose No. 1.
![]() |
Remove the 2 bolts, nut, and water inlet housing.
![]() |
Remove the 2 O-rings.
| 23. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1) |
![]() |
Remove the 12 bolts, seal washer, head cover and gasket.
![]() |
Remove the 3 gaskets.
| 24. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2) |
![]() |
Remove the 12 bolts, seal washer, head cover and gasket.
![]() |
Remove the 3 gaskets.
| 25. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
![]() |
Insert the blade of SST between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
Using "Torx" socket wrench E6, remove the 2 stud bolts.
| 26. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the bolt, 2 nuts, oil strainer and gasket.
Using "Torx" socket wrench E6, remove the 2 stud bolts.
| 27. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
![]() |
Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
![]() |
Remove the 2 O-rings.
Using "Torx" socket wrench E8, remove the 2 stud bolts.
| 28. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 23 bolts and 2 nuts as shown in the illustration.
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
![]() |
Remove the gasket.
| 29. REMOVE TIMING CHAIN CASE OIL SEAL |
![]() |
Using a screwdriver, pry out the oil seal.