FUEL INJECTOR > INSTALLATION |
| 1. INSTALL FUEL INJECTOR ASSEMBLY |
![]() |
Apply a light coat of spindle oil or gasoline to new O-rings, and install them to each injector.
![]() |
Apply a light coat of spindle oil or gasoline where the fuel delivery pipe contacts the O-ring.
Push the fuel injector while turning it to install the injector in the fuel delivery pipe.
Position the fuel injector connector outward.
![]() |
Install 6 new insulators to the intake manifold.
![]() |
Place the fuel delivery pipe and the 6 fuel injectors together to the intake manifold.
Temporarily install the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.
Tighten the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.
![]() |
Connect the 6 fuel injector connectors.
| 2. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Push in the tube connector to the pipe until the tube connector makes a "click" sound.
Install the No. 2 fuel pipe clamp.
| 3. INSTALL INTAKE AIR SURGE TANK ASSEMBLY |
| Tightening Parts | ||
| Surge Tank and Intake Manifold | ||
| No. 1 Surge Tank Stay and Surge Tank | ||
| Throttle Body Bracket and Surge Tank |
![]() |
Install a new gasket to the intake air surge tank.
Using a 5 mm hexagon socket wrench, install the 4 bolts.
Install the intake air surge tank with the 2 nuts and 2 bolts.
![]() |
Connect the connector.
![]() |
Install the vacuum hose clamp with the bolt.
![]() |
Connect the union to check valve hose.
Connect the No. 1 ventilation hose.
![]() |
Install the clamp and connect the throttle with motor body assembly connector.
Connect the vapor feed hose.
Connect the 2 water by-pass hoses to the throttle with motor body assembly.
| 4. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner cap sub-assembly, and connect the 3 bands.
![]() |
Connect the mass air flow meter connector (*1).
Connect the No. 2 ventilation hose (*2).
Connect the hose band (*3).
![]() |
Connect the 3 vacuum hoses.
| 5. ADD ENGINE COOLANT |
Close the radiator drain cock plug and 2 cylinder block drain cock plugs.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reservoir tank cap.
Start the engine, and warm it up.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 7. CHECK FOR ENGINE COOLANT LEAKS |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 8. CHECK FOR FUEL LEAKS |
| 9. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY |
![]() |
Install the cowl top panel outer sub-assembly with the 4 bolts and 4 nuts.
| 10. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Install the windshield wiper motor and link assembly with the 4 bolts.
![]() |
Connect the connector.
| 11. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Engage the 4 claws and install the cowl top ventilator louver sub-assembly.
Install the 2 clips.
| 12. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Engage the claw and install the front fender to cowl side seal RH.
| 13. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Engage the claw and install the front fender to cowl side seal LH.
| 14. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
Clean the wiper arm serrations.
When reinstalling:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 37 to 52 mm (1.46 to 2.05 in.) |
| 15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
Clean the wiper arm serrations.
When reinstalling:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 23 to 38 mm (0.90 to 1.49 in.) |
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 16. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Fit the 3 retainers and install the V-bank cover.