FRONT DRIVE SHAFT > DISASSEMBLY |
| 1. REMOVE FRONT DRIVE SHAFT LH HOLE SNAP RING |
![]() |
Using a screwdriver, remove the front drive shaft LH hole snap ring.
| 2. REMOVE NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP (for 2GR-FE) |
![]() |
Using pliers, remove the No. 2 front axle inboard joint boot clamp as shown in the illustration.
| 3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP (for 2GR-FE) |
Remove the front axle inboard joint boot clamp.
| 4. REMOVE NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP (for 2AZ-FE) |
![]() |
For one touch type:
Using a screwdriver, remove the No. 2 front axle inboard joint boot clamp as shown in the illustration.
For claw engagement type:
Using needle-nose pliers, remove the No. 2 front axle inboard joint boot clamp as shown in the illustration.
| 5. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP (for 2AZ-FE) |
Remove the front axle inboard joint boot clamp.
| 6. SEPARATE FRONT AXLE INBOARD JOINT BOOT |
Separate the front axle inboard joint boot from the inboard joint assembly.
| 7. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY |
Remove the grease from the inboard joint assembly.
![]() |
Put matchmarks on the inboard joint assembly and outboard joint shaft.
Remove the inboard joint assembly from the outboard joint shaft.
![]() |
Using a snap ring expander, remove the shaft snap ring.
![]() |
Put matchmarks on the outboard joint shaft and tripod joint.
Using a brass bar and a hammer, remove the tripod joint from the outboard joint shaft.
| 8. REMOVE INBOARD JOINT BOOT |
Remove the inboard joint boot from the outboard joint shaft.
| 9. REMOVE FRONT DRIVE SHAFT DAMPER LH (for 2GR-FE) |
![]() |
Using pliers, remove the drive shaft damper clamp as shown in the illustration.
Remove the drive shaft damper.
| 10. REMOVE FRONT DRIVE SHAFT DAMPER RH (for 2GR-FE) |
Remove the front drive shaft damper RH.
| 11. REMOVE FRONT DRIVE SHAFT DAMPER LH (for 2AZ-FE, Automatic Transaxle) |
![]() |
For one touch type:
Using a screwdriver, remove the drive shaft damper clamp as shown in the illustration.
For claw engagement type:
Using needle-nose pliers, remove the drive shaft damper clamp as shown in the illustration.
Remove the drive shaft damper.
| 12. REMOVE FRONT DRIVE SHAFT DAMPER RH (for 2AZ-FE) |
Remove the front drive shaft damper RH.
| 13. REMOVE NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for 2GR-FE) |
![]() |
Using pliers, remove the No. 2 front axle outboard joint boot clamp as shown in the illustration.
| 14. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for 2GR-FE) |
Remove the front axle outboard joint boot clamp.
| 15. REMOVE NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for 2AZ-FE) |
![]() |
Using a screwdriver, remove the No. 2 front axle outboard joint boot clamp as shown in the illustration.
| 16. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for 2AZ-FE) |
Remove the front axle outboard joint boot clamp.
| 17. REMOVE FRONT AXLE OUTBOARD JOINT BOOT |
Remove the outboard joint boot from the outboard joint shaft.
Remove the grease from the outboard joint.
| 18. REMOVE FRONT DRIVE SHAFT DUST COVER LH |
![]() |
Using SST and a press, remove the drive shaft dust cover LH.
| 19. REMOVE FRONT DRIVE SHAFT DUST COVER RH |
![]() |
Using a press, remove the drive shaft dust cover RH.
| 20. REMOVE FRONT DRIVE SHAFT DUST COVER |
![]() |
Using SST and a press, remove the drive shaft dust cover.
| 21. REMOVE FRONT DRIVE SHAFT BEARING |
![]() |
Using a snap ring expander, remove the drive shaft hole snap ring.
![]() |
Using SST and a press, remove the bearing.
Remove the bearing bracket hole snap ring.