FRONT DRIVE SHAFT > REASSEMBLY |
| 1. INSTALL FRONT DRIVE SHAFT BEARING |
![]() |
Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.
Using SST and a steel plate, install a new front drive shaft bearing.
![]() |
Using a snap ring expander, install a new drive shaft hole snap ring.
| 2. INSTALL FRONT DRIVE SHAFT DUST COVER |
![]() |
Using SST and a press, install a new drive shaft dust cover.
| 3. INSTALL FRONT DRIVE SHAFT DUST COVER RH |
![]() |
Using SST and a press, install a new drive shaft dust cover RH until distance (A) from the tip of the center drive shaft to the drive shaft dust cover RH meets the specification.
| Engine type | Distance (A) |
| 2GR-FE | 110.0 to 111.0 mm (4.3307 to 4.3701 in.) |
| 2AZ-FE | 91.0 to 92.0 mm (3.5827 to 3.6220 in.) |
| 4. INSTALL FRONT DRIVE SHAFT DUST COVER LH |
![]() |
Using SST and a press, install a new drive shaft dust cover LH.
| 5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT |
![]() |
Hold the drive shaft lightly in a vise between aluminium plates.
Temporarily install a new outboard joint boot to the drive shaft with the 2 clamps.
Pack the outboard joint shaft and boot with grease.
| Engine type | Grease capacity |
| 2GR-FE | 164 to 184 g (5.8 to 6.5 oz.) |
| 2AZ-FE | 190 to 200 g (6.7 to 7.1 oz.) |
| 6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for 2GR-FE) |
![]() |
Hold the drive shaft lightly in a vise between aluminum plates.
Install the 2 outboard joint boot clamps onto the boot.
Place SST onto the outboard joint boot clamp.
Tighten the SST so that the outboard joint boot clamp is pinched.
![]() |
Using SST, measure the clearance of the outboard joint boot clamp.
| 7. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for 2AZ-FE) |
![]() |
Install the front axle outboard joint boot clamp onto the outboard joint boot and temporarily fold back the lever.
![]() |
Using water pump pliers, pinch the boot clamp to temporarily secure it.
![]() |
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.
| 8. INSTALL NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for 2GR-FE) |
Install the No. 2 outboard joint boot clamp onto the boot.
![]() |
Place SST onto the No. 2 outboard joint boot clamp.
Tighten the SST so that the No. 2 outboard joint boot clamp is pinched.
![]() |
Using SST, measure the clearance of the No. 2 outboard joint boot clamp.
| 9. INSTALL NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for 2AZ-FE) |
![]() |
Install the No. 2 front axle outboard joint boot clamp onto the outboard joint boot and temporarily fold back the lever.
![]() |
Lean your weight on your hand and roll the outboard joint forward while pressing the outboard joint against the work plane. Roll the outboard joint and fold the lever until a click sound can be heard.
![]() |
Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.
| 10. INSTALL FRONT DRIVE SHAFT DAMPER LH (for 2GR-FE) |
![]() |
Install the drive shaft damper to the drive shaft.
Make sure that the damper is on the shaft groove.
Set the distance as specified below.
Install the drive shaft damper clamp onto the drive shaft damper.
![]() |
Place SST onto the drive shaft damper clamp.
Tighten the SST so that the clamp is pinched.
![]() |
Using SST, measure the clearance of the drive shaft damper clamp.
| 11. INSTALL FRONT DRIVE SHAFT DAMPER RH (for 2GR-FE) |
Install the front drive shaft damper RH.
| 12. INSTALL FRONT DRIVE SHAFT DAMPER LH (for 2AZ-FE, Automatic Transaxle) |
![]() |
Install the drive shaft damper to the drive shaft.
Make sure that the damper is on the shaft groove.
Set the distance as specified below.
![]() |
Using a screwdriver, install a new drive shaft damper clamp as shown in the illustration.
| 13. INSTALL FRONT DRIVE SHAFT DAMPER RH (for 2AZ-FE) |
![]() |
Install the drive shaft damper to the drive shaft.
Make sure that the damper is on the shaft groove.
Set the distance as specified below.
![]() |
Using a screwdriver, install a new drive shaft damper clamp as shown in the illustration.
| 14. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY |
![]() |
Temporarily install a new inboard joint boot to the drive shaft with the 2 clamps.
Place the beveled side of the tripod joint axial spline toward the outboard joint shaft.
Align the matchmarks.
Using a brass bar and hammer, tap in the tripod joint to the outboard joint shaft.
![]() |
Using a snap ring expander, install a new shaft snap ring.
Coat the outboard joint shaft and boot with grease.
| Engine type | Grease capacity |
| 2GR-FE | 155 to 175 g (5.5 to 6.2 oz.) |
| 2AZ-FE | 175 to 185 g (6.2 to 6.5 oz.) |
![]() |
Align the matchmarks and install the inboard joint assembly to the outboard joint shaft assembly.
| 15. INSTALL FRONT AXLE INBOARD JOINT BOOT |
Install the inboard joint boot to the inboard joint assembly.
![]() |
Check whether the drive shaft dimensions are within the following specifications.
| Engine Type | LH | RH |
| 2GR-FE | 585.5 to 589.5 mm (23.05 to 23.21 in.) | 904.4 to 908.4 mm (35.61 to 35.76 in.) |
| 2AZ-FE | 592.2 to 602.2 mm (23.32 to 23.71 in.) | 891.0 to 901.0 mm (35.08 to 35.47 in.) |
| 16. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP (for 2GR-FE) |
![]() |
Hold the drive shaft lightly in a vise between aluminum plates.
Install the 2 inboard joint boot clamps onto the boot.
Place SST onto the inboard joint boot clamp.
Tighten the SST so that the inboard joint boot clamp is pinched.
![]() |
Using SST, measure the clearance of the inboard joint boot clamp.
| 17. INSTALL NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP (for 2GR-FE) |
Hold the inboard joint shaft assembly in a vise between aluminium plates.
Install the No. 2 front axle inboard joint boot clamp onto the boot.
![]() |
Place SST onto the No. 2 front axle inboard joint boot clamp.
Tighten the SST so that the No. 2 front axle inboard joint boot clamp is pinched.
![]() |
Using SST, measure the clearance of the No. 2 front axle inboard joint boot clamp.
| 18. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP (for 2AZ-FE) |
![]() |
For one touch type:
Using a screwdriver, install the inboard joint boot clamp as shown in the illustration.
For claw engagement type:
Using needle nose pliers, install the inboard joint boot clamp as shown in the illustration.
| 19. INSTALL NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP (for 2AZ-FE) |
![]() |
For one touch type:
Using a screwdriver, install the No. 2 front axle inboard joint boot clamp as shown in the illustration.
For claw engagement type:
Using needle nose pliers, install the No. 2 front axle inboard joint boot clamp as shown in the illustration.
| 20. INSTALL FRONT DRIVE SHAFT LH HOLE SNAP RING |
Install a new hole snap ring.
| 21. INSPECT FRONT DRIVE SHAFT ASSEMBLY |
![]() |
Check that there is no excessive play in the outboard joint.
Check that the inboard joint slides smoothly in the thrust direction.
Check that there is no excessive play in the radial directions of the inboard joint.
Check the boots for damage.