ELECTRICAL KEY OSCILLATOR (for Front Door) > REMOVAL |
| 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Disengage the 2 clips and remove the front door lower frame bracket garnish.
| 2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.
| 3. REMOVE ASSIST GRIP COVER |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the assist grip cover.
| 4. REMOVE COURTESY LIGHT ASSEMBLY |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.
Disconnect the connector.
| 5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Remove the 3 screws and clip (A).
Using a clip remover, disengage the 9 clips.
![]() |
Pull up the front door trim board in the direction indicated by the arrow.
Disengage the reference bosses from the front door panel.
Raise the front door trim board to disengage the 4 claws and remove the front door trim board together with the front door inner glass weatherstrip.
![]() |
Disengage the 2 claws and disconnect the front door inside handle sub-assembly.
| 6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP |
![]() |
Using a screwdriver, disengage the 4 clips as shown in the illustration and remove the front door inner glass weatherstrip from the front door trim board.
| 7. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door inside handle sub-assembly.
| 8. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 4 bolts and front No. 1 speaker assembly.
| 9. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connector and each clamp, and remove the front door service hole cover.
| 10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
Connect the front power window regulator motor assembly connector.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
![]() |
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly as shown in the illustration.
Disconnect the power window regulator master switch assembly and front power window regulator motor assembly connector.
| 11. REMOVE FRONT DOOR OUTSIDE HANDLE COVER |
![]() |
Remove the hole plug.
Using a "TORX" socket wrench (T30), loosen the screw and remove the front door outside handle cover and the door lock key cylinder as a unit.
![]() |
Using a screwdriver, disengage the 2 claws and remove the front door outside handle cover.
| 12. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Disconnect the connector.
![]() |
Remove the front door outside handle assembly as shown in the illustration.
| 13. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD |
![]() |
Disengage the 3 claws and remove the front door front outside handle pad.
| 14. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD |
![]() |
Disengage the 2 claws and remove the front door rear outside handle pad.
| 15. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Disengage the 2 clamps.
Disengage the claws and remove the front door outside handle frame sub-assembly.
| 16. REMOVE DOOR ELECTRICAL KEY OSCILLATOR |
![]() |
Remove the screw and door electrical key oscillator.