Home › BODY ELECTRICAL › DOOR LOCK › ELECTRICAL KEY OSCILLATOR (for Front Floor)

ELECTRICAL KEY OSCILLATOR (for Front Floor) > REMOVAL

for Preparation Click here



1. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side .



2. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side .



3. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY


    B133988E01
  1. Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.



4. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the bolt <A>.



    B133992E01
  1. Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.



5. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)


    B226062
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



6. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B137272
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



7. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226063
  1. Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.



8. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226064
  1. Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.



9. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle)


    B226065
  1. Disengage the 6 claws and the 3 clips, and then remove the floor shift position indicator housing sub-assembly.

  1. with Seat Heater System:

    1. Disconnect each connector.



10. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)


    B137274E01
  1. Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.



    B137275
  1. Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.

  1. with Seat Heater System:

    1. Disconnect each connector.



11. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle)


    B226097
  1. Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.



12. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)


    B137277
  1. Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.



13. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B133997E01
  1. Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the upper console panel sub-assembly.

    HINT:
    Set the shift lever in the D position.



14. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.



15. REMOVE CONSOLE BOX CARPET


    B134004
  1. Remove the console box carpet.



16. REMOVE CONSOLE BOX ASSEMBLY


    B134002E01
  1. Remove the 2 screws <F>.



    B134003E01
  1. Remove the 2 bolts <G> and the console box assembly.



17. REMOVE NO. 1 CONSOLE BOX INSERT FRONT


    B134006E01
  1. Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.



18. REMOVE FLOOR CARPET BRACKET RH


    E129147E01
  1. Release the clamp.

  1. Turn back the floor carpet.



    E128513
  1. Remove the 3 clips.

  1. Remove the floor carpet bracket RH.



19. REMOVE ELECTRICAL KEY OSCILLATOR


    B223350E01
  1. Disengage the clamp to remove the electrical key oscillator.