SFI SYSTEM > VC Output Circuit |



| 1.CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to the ON position.
|
| ||||
| NG | |
| 2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Check the communication between the tester and ECM.
| Result | Proceed to |
| Communication is possible | A |
| Communication is not possible | B |
|
| ||||
| B | |
| 3.CHECK THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED) |
Disconnect the throttle body connector.
Turn the ignition switch to the ON position.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the throttle body connector.
|
| ||||
| B | |
| 4.CHECK ACCELERATOR PEDAL ASSEMBLY (CHECK MIL ILLUMINATED) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to the ON position.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the accelerator pedal position sensor connector.
|
| ||||
| B | |
| 5.CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED) |
Disconnect the connector from the VVT sensor for intake camshaft bank 1.
Turn the ignition switch to the ON position.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the connector to the VVT sensor for intake camshaft bank 1.
|
| ||||
| B | |
| 6.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED) |
Disconnect the connector from the VVT sensor for exhaust camshaft bank 1.
Turn the ignition switch to the ON position.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the connector to the VVT sensor for exhaust camshaft bank 1.
|
| ||||
| B | |
| 7.CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED) |
Disconnect the connector from the VVT sensor for intake camshaft bank 2.
Turn the ignition switch to the ON position.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the connector to the VVT sensor for intake camshaft bank 2.
|
| ||||
| B | |
| 8.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED) |
Disconnect the connector from the VVT sensor for exhaust camshaft bank 2.
Turn the ignition switch to the ON position.
Check the MIL.
| Result | Proceed to |
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the connector to the VVT sensor for exhaust camshaft bank 2.
|
| ||||
| B | |
| 9.CHECK HARNESS AND CONNECTOR |
![]() |
Disconnect the throttle body connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the the connector from VVT sensor for intake camshaft bank 1.
Disconnect the connector from the VVT sensor for exhaust camshaft bank 1.
Disconnect the connector from the VVT sensor for intake camshaft bank 2.
Disconnect the connector from the VVT sensor for exhaust camshaft bank 2.
Disconnect the C58 (RHD) and A24 (RHD), or C55 (LHD) and A55 (LHD) ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VCTA (C58-96) - Body ground | 10 kΩ or higher |
| VCV1 (C58-115) - Body ground | 10 kΩ or higher |
| VCV2 (C58-113) - Body ground | 10 kΩ or higher |
| VCE1 (C58-114) - Body ground | 10 kΩ or higher |
| VCE2 (C58-112) - Body ground | 10 kΩ or higher |
| VCPA (A24-57) - Body ground | 10 kΩ or higher |
| VCP2 (A24-58) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| VCTA (C55-96) - Body ground | 10 kΩ or higher |
| VCV1 (C55-115) - Body ground | 10 kΩ or higher |
| VCV2 (C55-113) - Body ground | 10 kΩ or higher |
| VCE1 (C55-114) - Body ground | 10 kΩ or higher |
| VCE2 (C55-112) - Body ground | 10 kΩ or higher |
| VCPA (A55-57) - Body ground | 10 kΩ or higher |
| VCP2 (A55-58) - Body ground | 10 kΩ or higher |
Reconnect the ECM connectors.
Reconnect the fuel pressure sensor connector.
Reconnect the connector to the VVT sensor for exhaust camshaft bank 2.
Reconnect the connector to the VVT sensor for intake camshaft bank 2.
Reconnect the connector to the VVT sensor for exhaust camshaft bank 1.
Reconnect the connector to the VVT sensor for intake camshaft bank 1.
Reconnect the accelerator pedal position sensor connector.
Reconnect the throttle body connector.
|
| ||||
| OK | ||
| ||