Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY

for Preparation Click here


NOTICE:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.



1. REMOVE VERTICAL ADJUSTER COVER LH (for Driver Seat)


    B139103
  1. Using a screwdriver, disengage the 2 claws and remove the vertical adjuster cover LH.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE VERTICAL ADJUSTING HANDLE NO. 2 (for Driver Seat)


    B139104
  1. Remove the 2 screws and vertical adjusting handle.



3. REMOVE RECLINING ADJUSTER RELEASE HANDLE


    B139105
  1. Lift the reclining adjuster release handle.

  1. Using a screwdriver, disengage the claw and remove the reclining adjuster release handle.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE FRONT SEAT CUSHION SHIELD


    B139108
  1. Disengage the 2 hooks.



    B139106
  1. Remove the 3 screws.

  1. Disengage the 2 claws and remove the front seat cushion shield.



5. REMOVE LOWER SEAT TRACK SPACER


    B139122
  1. Remove the 2 screws and lower seat track spacer.



6. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    B132032E02
  1. for Driver seat:

    1. Disconnect the connectors and disengage the 4 clamps.

  1. for Passenger seat:

    1. Disconnect the connector and disengage the 3 clamps.



    B132034
  1. Remove the nut and front seat inner belt assembly.



7. REMOVE FRONT INNER SEAT CUSHION SHIELD


    B139107
  1. Remove the screw.

  1. Disengage the claw and clip, and then remove the front inner seat cushion shield.



8. REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER WITH PAD


    B139123E01
  1. Disengage the clamp.

  1. Disengage the hooks and remove the front separate type seat cushion cover with pad.



9. REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER


    B139121E01
  1. Remove the 16 hog rings and front separate type seat cushion cover.



10. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY


    B134682E01
  1. Remove the 2 screws.

  1. Disconnect the 14 clamps and front separate type seatback cover.

  1. Pull the seat back board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.



11. REMOVE FRONT SEAT HEADREST SUPPORT


    B134683
  1. Detach the 2 claws and remove the headrest support.



12. REMOVE FRONT SEAT HEADREST SUPPORT


13. REMOVE FRONT SEPARATE TYPE SEATBACK COVER WITH PAD


    B139109
  1. Disengage the 3 hooks.



    B139110E01
  1. Remove the 2 hog rings.



    B139111
  1. Remove the nut and separate the 2 brackets.

  1. Remove the front separate type seatback cover with pad.



14. REMOVE FRONT SEPARATE TYPE SEATBACK COVER


    B139112E01
  1. Remove the 10 hog rings and front separate type seatback cover.



15. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B233419E01
  1. Disengage the 5 clamps and disconnect the wire harness.



    B233421E01
  1. Disengage the 2 clamps and disconnect the wire harness.

  1. Remove the 2 nuts and front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



16. REMOVE RECLINING ADJUSTER INSIDE COVER LH
  1. Disconnect the clamp.



    B139113
  1. Remove the screw.

  1. Disengage the claw and remove the reclining adjuster inside cover LH.



17. REMOVE RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedures for the RH side and LH side.



18. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    B139114
  1. Remove the screw and reclining adjuster inside cover LH.



19. REMOVE RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedures for the RH side and LH side.



20. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH


    B139115
  1. Using a screwdriver, disengage the claw and remove the front lower seat cushion shield LH.



21. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH

HINT:
Use the same procedures for the RH side and LH side.



22. REMOVE SEAT POSITION SENSOR (for Driver Seat)


    C133900
  1. Disconnect the connector.

  1. Using a "TORX" socket (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.



    C133901
  1. Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.