Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Manual Seat)

FRONT SEAT SIDE AIRBAG ASSEMBLY (for Manual Seat) > REMOVAL

for Preparation Click here


CAUTION:
  1. Be sure to read Precaution thoroughly before servicing (Click here).
  2. If the side airbag was deployed, replace the front seat assembly with a new one.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.



2. REMOVE FRONT SEAT HEADREST ASSEMBLY


3. REMOVE SEAT TRACK COVER
  1. Move the front seat assembly fully forward by operating the slide handle.



    B139099
  1. Using a screwdriver, disengage the 4 claws and remove the seat track cover.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE INNER SEAT TRACK BRACKET COVER


    B139100
  1. Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE FRONT SEAT ASSEMBLY
  1. Move the front seat assembly to the rearmost position by operating the slide handle.



    B139101
  1. Remove the 2 bolts on the front seat track bracket.

  1. Move the front seat assembly fully forward by operating the slide handle.



    B139102
  1. Remove the 2 bolts on the rear seat track bracket.

  1. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.

  1. Disconnect the connectors and clamp.

  1. Remove the front seat assembly.



6. REMOVE VERTICAL ADJUSTER COVER LH (for Driver Seat)


    B139103
  1. Using a screwdriver, disengage the 2 claws and remove the vertical adjuster cover LH.

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE VERTICAL ADJUSTING HANDLE NO. 2 (for Driver Seat)


    B139104
  1. Remove the 2 screws and vertical adjusting handle.



8. REMOVE RECLINING ADJUSTER RELEASE HANDLE


    B139105
  1. Lift the reclining adjuster release handle.

  1. Using a screwdriver, disengage the claw and remove the reclining adjuster release handle.

    HINT:
    Tape the screwdriver tip before use.



9. REMOVE FRONT SEAT CUSHION SHIELD


    B139108
  1. Disengage the 2 hooks.



    B139106
  1. Remove the 3 screws.

  1. Disengage the 2 claws and remove the front seat cushion shield.



10. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    B132032E02
  1. for Driver seat:

    1. Disconnect the connectors and disengage the 4 clamps.

  1. for Passenger seat:

    1. Disconnect the connector and disengage the 3 clamps.



    B132034
  1. Remove the nut and front seat inner belt assembly.



11. REMOVE FRONT INNER SEAT CUSHION SHIELD


    B139107
  1. Remove the screw.

  1. Disengage the claw and clip, and then remove the front inner seat cushion shield.



12. REMOVE FRONT SEAT BACK BOARD SUB-ASSEMBLY


    B134682E01
  1. Remove the 2 screws.

  1. Disconnect the 14 clamps and front separate type seatback cover.

  1. Pull the seat back board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.



13. REMOVE FRONT SEAT HEADREST SUPPORT (for LH Side)


    B134683
  1. Detach the 2 claws and remove the headrest support.



14. REMOVE FRONT SEAT HEADREST SUPPORT (for RH Side)


15. REMOVE FRONT SEATBACK COVER WITH PAD


    B139109
  1. Disengage the 3 hooks.



    B139110E01
  1. Remove the 2 hog rings.



    B139111
  1. Remove the nut and separate the 2 brackets.

  1. Remove the front separate type seatback cover with pad.



16. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B233419E01
  1. Disengage the 5 clamps and disconnect the wire harness.



    B233421E01
  1. Disengage the 2 clamps and disconnect the wire harness.

  1. Remove the 2 nuts and front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.