FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY |
| 1. REMOVE VERTICAL ADJUSTER COVER LH (for Driver Seat) |
![]() |
Using a screwdriver, disengage the 2 claws and remove the vertical adjuster cover LH.
| 2. REMOVE VERTICAL ADJUSTING HANDLE NO. 2 (for Driver Seat) |
![]() |
Remove the 2 screws and vertical adjusting handle.
| 3. REMOVE RECLINING ADJUSTER RELEASE HANDLE |
![]() |
Lift the reclining adjuster release handle.
Using a screwdriver, disengage the claw and remove the reclining adjuster release handle.
| 4. REMOVE FRONT SEAT CUSHION SHIELD |
![]() |
Disengage the 2 hooks.
![]() |
Remove the 3 screws.
Disengage the 2 claws and remove the front seat cushion shield.
| 5. REMOVE LOWER SEAT TRACK SPACER |
![]() |
Remove the 2 screws and lower seat track spacer.
| 6. REMOVE FRONT SEAT INNER BELT ASSEMBLY |
![]() |
for Driver seat:
Disconnect the connectors and disengage the 4 clamps.
for Passenger seat:
Disconnect the connector and disengage the 3 clamps.
![]() |
Remove the nut and front seat inner belt assembly.
| 7. REMOVE FRONT INNER SEAT CUSHION SHIELD |
![]() |
Remove the screw.
Disengage the claw and clip, and then remove the front inner seat cushion shield.
| 8. REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER WITH PAD |
![]() |
Disengage the clamp.
Disengage the hooks and remove the front separate type seat cushion cover with pad.
| 9. REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER |
![]() |
Remove the 16 hog rings and front separate type seat cushion cover.
| 10. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY |
![]() |
Remove the 2 screws.
Disconnect the 14 clamps and front separate type seatback cover.
Pull the seat back board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.
| 11. REMOVE FRONT SEAT HEADREST SUPPORT |
![]() |
Detach the 2 claws and remove the headrest support.
| 12. REMOVE FRONT SEAT HEADREST SUPPORT |
| 13. REMOVE FRONT SEPARATE TYPE SEATBACK COVER WITH PAD |
![]() |
Disengage the 3 hooks.
![]() |
Remove the 2 hog rings.
![]() |
Remove the nut and separate the 2 brackets.
Remove the front separate type seatback cover with pad.
| 14. REMOVE FRONT SEPARATE TYPE SEATBACK COVER |
![]() |
Remove the 10 hog rings and front separate type seatback cover.
| 15. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY |
![]() |
Disengage the 5 clamps and disconnect the wire harness.
![]() |
Disengage the 2 clamps and disconnect the wire harness.
Remove the 2 nuts and front seat side airbag assembly.
| 16. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
Disconnect the clamp.
![]() |
Remove the screw.
Disengage the claw and remove the reclining adjuster inside cover LH.
| 17. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
| 18. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw and reclining adjuster inside cover LH.
| 19. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
| 20. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH |
![]() |
Using a screwdriver, disengage the claw and remove the front lower seat cushion shield LH.
| 21. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH |
| 22. REMOVE SEAT POSITION SENSOR (for Driver Seat) |
![]() |
Disconnect the connector.
Using a "TORX" socket (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.
![]() |
Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.