Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Manual Seat)

FRONT SEAT SIDE AIRBAG ASSEMBLY (for Manual Seat) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



    B233421E01
  1. Install the front seat side airbag assembly with 2 new nuts.

  1. Engage the 2 clamps to connect the wire harness.



    B233419E01
  1. Engage the 5 clamps to connect the wire harness.



2. INSTALL FRONT SEATBACK COVER WITH PAD


    B139111
  1. Fully cover the airbag with the 2 seatback cover brackets and tighten the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the seat back cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B140573E01
  1. Using hog ring pliers, install the front separate type seatback cover with pad to the seat frame with 2 new hog rings, and attach the hooks.



    B139109
  1. Engage the 3 hooks.



3. INSTALL FRONT SEAT HEADREST SUPPORT (for LH Side)


4. INSTALL FRONT SEAT HEADREST SUPPORT (for RH Side)


5. INSTALL FRONT SEAT BACK BOARD SUB-ASSEMBLY


6. INSTALL FRONT INNER SEAT CUSHION SHIELD


7. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    B132035E01
  1. Install the front seat inner belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.



    B132032E02
  1. for Driver seat:

    1. Connect the connectors and engage the 4 clamps.

  1. for Passenger seat:

    1. Connect the connector and engage the 3 clamps.



8. INSTALL FRONT SEAT CUSHION SHIELD


9. INSTALL RECLINING ADJUSTER RELEASE HANDLE


10. INSTALL VERTICAL ADJUSTING HANDLE NO. 2 (for Driver Seat)


11. INSTALL VERTICAL ADJUSTER COVER LH (for Driver Seat)


12. INSTALL FRONT SEAT ASSEMBLY
  1. Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

  1. Connect the connector and clamp.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.



    B139101
  1. Temporarily install the front seat track bracket with the 2 bolts.

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.



    B139102
  1. Temporarily install the rear seat track bracket with the 2 bolts.

  1. Move the front seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



13. INSTALL INNER SEAT TRACK BRACKET COVER


    B139100E01
  1. Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the seat track bracket cover inner to engage claw B.



14. INSTALL SEAT TRACK COVER


    B139099E01
  1. Slide the seat track cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the seat track cover to engage claw B.



15. INSTALL FRONT SEAT HEADREST ASSEMBLY


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


17. INSPECT SLIDE ADJUSTER LOCK


18. INSPECT SRS WARNING LIGHT
Check the SRS warning light (Click here).