Home › ENGINE ยท 2GR-FE › CHARGING › GENERATOR

GENERATOR > INSTALLATION

for Preparation Click here



1. INSTALL GENERATOR ASSEMBLY


    A135391
  1. Install the bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A128066
  1. Install the wire harness clamp stay with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    A133867
  1. Connect the wire harness clamp.

  1. Install the generator assembly to the cylinder block with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A133866
  1. Install the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A133865
  1. Connect the generator connector to the generator assembly.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the 2 wire harness clamps.

  1. Connect the magnetic clutch connector to the compressor and magnetic clutch.



2. INSTALL V-RIBBED BELT


    A129622E01
  1. Install the V-ribbed belt.

  1. Using SST, turn the belt tensioner counterclockwise and remove the bar.

    SST
    09249-63010  



    A129623E01
  1. If it is difficult to install the V-ribbed belt, perform the following procedure:

    1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

    2. While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the tensioner pulley.

      NOTICE:
      1. Put the backside of the V-ribbed belt on the tensioner pulley and idler pulley.
      2. Check that the V-ribbed belt is properly set to each pulley.

    3. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the belt has not slipped out of the grooves on the bottom of the crank pulley by hand.



3. INSTALL RADIATOR ASSEMBLY


    A135523
  1. Install the radiator to the body.



    A133370
  1. Install the condenser assembly with the 4 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL FAN SHROUD


    A143825E01
  1. Install the fan assembly with motor to the radiator with the 2 guides at the bottom and 3 snap fits on the top.



    A139341E01
  1. Connect the fan motor connector.



5. INSTALL RADIATOR SUPPORT UPPER


    A133369
  1. Install the radiator support upper with the 5 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



    A133367
  1. Install the hood lock assembly to the radiator support upper with the 3 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }



    A133368
  1. For LHD:
    Install the hood lock control cable assembly to the radiator support upper with the clamp.



    A139356
  1. For RHD:
    Install the hood lock control cable assembly to the radiator support upper with the clamp.

  1. Connect the 2 horn connectors.



6. CONNECT NO. 1 OIL COOLER OUTLET TUBE


    A133366
  1. Connect the No. 1 oil cooler outlet tube to the radiator assembly.



7. CONNECT NO. 1 OIL COOLER INLET TUBE


    A133365
  1. Connect the No. 1 oil cooler inlet tube to the radiator assembly.



8. CONNECT RADIATOR OUTLET HOSE


    A133364
  1. Connect the radiator hose outlet to the radiator assembly.



9. CONNECT RADIATOR INLET HOSE


    A133363
  1. Connect the radiator hose inlet to the radiator assembly.



10. CONNECT RADIATOR RESERVE TANK HOSE


    A133362
  1. Connect the radiator reservoir tank hose to the radiator assembly.



11. INSTALL FRONT BUMPER ENERGY ABSORBER


    B220950
  1. Engage the 2 guides and install the front bumper energy absorber to the front bumper reinforcement sub-assembly.



12. INSTALL FRONT BUMPER ASSEMBLY


  1. w/ Headlight Cleaner System:



      B137737
    1. Connect the headlight cleaner washer hose.

  1. Connect each connector.

  1. w/ TOYOTA Parking Assist-sensor System:

    1. Connect the No. 1 ultrasonic sensor connector and engage the clamp.



    B221322
  1. Engage the 2 claws.

    HINT:
    Use the same procedure for the RH side and LH side.



    B220944
  1. Install the front bumper assembly with the 8 screws, 2 clips, 2 radiator grille protectors and bolt.



    B221988E01
  1. Install the pin hold clip.

    NOTICE:
    Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is vertical.

    HINT:
    Use the same procedure for the RH side and LH side.



    B220943E01
  1. Remove the applied protective tape on the front bumper assembly.



13. INSTALL NO. 1 AIR CLEANER INLET


    A132970
  1. Install the No. 1 air cleaner inlet with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



14. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A135706
  1. Install the air cleaner cap sub-assembly, and connect the 3 bands.



    A135705E01
  1. Connect the mass air flow meter connector (*1).

  1. Connect the No. 2 ventilation hose (*2).

  1. Connect the hose band (*3).



    A135704
  1. Connect the 3 vacuum hoses.



15. INSTALL AIR CLEANER INLET ASSEMBLY


    A132969
  1. Install the air cleaner inlet with the clamp and 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.9 N*m{ 70 kgf*cm , 61 in.*lbf }



17. ADD ENGINE COOLANT
  1. Close the radiator drain cock plug and 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Specified capacity:
    9.0 liters (9.5 US qts, 7.9 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Contact your TOYOTA dealer for further details.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap sub-assembly and reservoir tank cap.

  1. Start the engine, and warm it up.

    HINT:
    Adjust the air conditioner set temperature to MAX (HOT).

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



18. CHECK FOR ENGINE COOLANT LEAKS

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch OFF.



    A133894
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



19. INSTALL V-BANK COVER SUB-ASSEMBLY


    A132968
  1. Engage the 3 retainers to install the V-bank cover.



20. INSTALL COOL AIR INTAKE DUCT SEAL


    A132967
  1. Install the intake duct seal with the 7 clips.



21. INSTALL ENGINE UNDER COVER RH


22. INSTALL ENGINE UNDER COVER LH


23. INSTALL FRONT FENDER APRON SEAL RH


24. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }