Home › ENGINE ยท 2GR-FE › CHARGING › GENERATOR

GENERATOR > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE FRONT WHEEL RH


3. REMOVE FRONT FENDER APRON SEAL RH


4. REMOVE ENGINE UNDER COVER RH


5. REMOVE ENGINE UNDER COVER LH


6. REMOVE COOL AIR INTAKE DUCT SEAL


    A132967
  1. Remove the 7 clips and intake duct seal.



7. REMOVE V-BANK COVER SUB-ASSEMBLY


    A132968
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.



8. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap sub-assembly from the radiator assembly.



  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.


    A128117E02

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



9. REMOVE AIR CLEANER INLET ASSEMBLY


    A132969
  1. Remove the 2 bolts, clamp and air cleaner inlet.



10. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A135704
  1. Disconnect the 3 vacuum hoses.



    A135705E01
  1. Disconnect the mass air flow meter connector (*1).

  1. Disconnect the No. 2 ventilation hose (*2).

  1. Disconnect the hose band (*3).



    A135706
  1. Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.



11. REMOVE NO. 1 AIR CLEANER INLET


    A132970
  1. Remove the bolt and No. 1 air cleaner inlet.



12. REMOVE FRONT BUMPER ASSEMBLY (w/o Headlight Cleaner System)


    B140159E01
  1. Put protective tape around the front bumper assembly.



    B138884E01
  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedures for the RH side and LH side.



    B137735
  1. Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.



    B137736
  1. Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedures for the RH side and LH side.

  1. Disconnect each connector, and then remove the front bumper assembly.



13. REMOVE FRONT BUMPER ASSEMBLY (w/ Headlight Cleaner System)


    B137734E01
  1. Put protective tape around the front bumper assembly.



    B138884E01
  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedures for the RH side and LH side.



    B140161
  1. Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.



    B140160
  1. Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedures for the RH side and LH side.

  1. Disconnect each connector.



    B137737
  1. Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.



14. REMOVE FRONT BUMPER ENERGY ABSORBER


    B137728
  1. Remove the front bumper energy absorber from the front bumper reinforcement sub-assembly.



15. SEPARATE RADIATOR RESERVE TANK HOSE


    A133362
  1. Separate the radiator reserve tank hose from the radiator assembly.



16. SEPARATE RADIATOR INLET HOSE


    A133363
  1. Separate the radiator inlet hose from the radiator assembly.



17. SEPARATE RADIATOR OUTLET HOSE


    A133364
  1. Separate the radiator outlet hose from the radiator assembly.



18. SEPARATE NO. 1 OIL COOLER INLET HOSE


    A133365
  1. Separate the No. 1 oil cooler inlet hose from the radiator assembly.



19. SEPARATE NO. 1 OIL COOLER OUTLET HOSE


    A133366
  1. Separate the No. 1 oil cooler outlet hose from the radiator assembly.



20. REMOVE RADIATOR SUPPORT UPPER
  1. Disconnect the horn connector.



    A133367
  1. Remove the 3 bolts and separate the hood lock assembly from the radiator support upper.



    A133368E01
  1. For LHD:
    Remove the clamp and separate the hood lock control cable from the radiator support upper.



    A139356
  1. For RHD:
    Remove the clamp and separate the hood lock control cable from the radiator support upper.



    A133369
  1. Remove the 5 bolts and radiator support upper.



21. REMOVE FAN SHROUD


    A139341E01
  1. Remove the 3 clamps and connector.



    A143825E01
  1. Release the 3 snap fits and lift the fan assembly with motor from the radiator.



22. REMOVE RADIATOR ASSEMBLY


    A133370
  1. Remove the 4 bolts and separate the condenser assembly from the radiator assembly.



    A133373
  1. Remove the radiator assembly from the body.



23. REMOVE V-RIBBED BELT


    A129622E01
  1. Using SST, release the belt tension by turning the belt tensioner counterclockwise, and remove the V-ribbed belt from the belt tensioner.

    SST
    09249-63010  



    A095070
  1. While turning the belt tensioner counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner.



24. REMOVE GENERATOR ASSEMBLY


    A133865
  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.

  1. Disconnect the connector from the compressor and magnetic clutch.

  1. Disconnect the 2 wire harness clamps.



    A133866
  1. Remove the 2 bolts.



    A133867
  1. Remove the bolt from the cylinder block.

  1. Disconnect the wire harness clamp and remove the generator assembly.



    A128066
  1. Remove the bolt and wire harness clamp stay.



    A135391
  1. Remove the bolt and bracket.