Home › SECURITIES › THEFT DETERRENT › THEFT DETERRENT SYSTEM (w/ Entry and Start System)

THEFT DETERRENT SYSTEM (w/ Entry and Start System) > Security Horn Circuit


DESCRIPTION

When the theft deterrent system is changed from the armed state to the alarm sounding state, the certification ECU transmits a signal to cause the security horn to sound.

WIRING DIAGRAM


B139452E05


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY HORN)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Press the intelligent tester main switch on.

  1. Select the item below in the Active Test and then check that the indicator operates.

    Smart (Certification ECU): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Horn
    Security horn
    ON/OFF
    -

    OK:
    The security horn assembly sounds and stops correctly when operated through the intelligent tester.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (S-HORN FUSE)
  1. Remove the S-HORN fuse from the engine room J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminal Connection
    Condition
    Specified Condition
    S-HORN fuse
    Always
    Below 1 Ω



NG
REPLACE S-HORN FUSE
OK


3.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (S-HORN RELAY)


    A135182E13
  1. Remove the engine room J/B from the engine room R/B and J/B.

  1. Connect a positive (+) lead from the battery to terminal 1G-1.

  1. Connect a negative (-) lead from the battery to terminal 1D-11.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Terminal Connection
    Condition
    Specified Condition
    1A-5 - Body ground
    Always
    10 to 14 V



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK - BATTERY)


    B074501E26
  1. Disconnect the 1G J/B connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Terminal Connection
    Condition
    Specified Condition
    1G-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (INCLUDING SECURITY HORN ASSEMBLY)


    B225464E01
  1. Disconnect the 1A J/B connector.

  1. Connect a positive (+) lead from the battery to terminal 1A-5.

  1. Connect a negative (-) lead from the battery to body ground.

  1. Check the operation of the horn.

    Standard:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1A-5
    Horn sounds
    Battery negative (-) → Body ground



NG
Go to step 7
OK


6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM J/B - CERTIFICATION ECU)


    B139453E02
  1. Disconnect the E75 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminal Connection
    Condition
    Specified Condition
    E75-20 (SH-) - 1D-11
    Always
    Below 1 Ω
    E75-20 (SH-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

7.INSPECT SECURITY HORN ASSEMBLY


  1. for RHD:



      B144348
    1. Remove the security horn assembly (Click here).

    2. Check the operation of the horn.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1
      Horn sounds
      Battery negative (-) → Horn body



  1. for LHD:



      B139440
    1. Remove the security horn assembly (Click here).

    2. Check the operation of the horn.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1
      Horn sounds
      Battery negative (-) → Horn body



NG
REPLACE SECURITY HORN ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM R/B AND J/B - SECURITY HORN ASSEMBLY)