HEADLIGHT ASSEMBLY > INSTALLATION |
| 1. INSTALL HEADLIGHT ASSEMBLY |
Connect each connector.
![]() |
Engage the clamp.
Install the headlight assembly with the bolt and 2 screws.
| 2. INSTALL FRONT BUMPER ASSEMBLY |
w/ Headlight Cleaner System:
![]() |
Connect the headlight cleaner washer hose.
Connect each connector.
w/ TOYOTA Parking Assist-sensor System:
Connect the No. 1 ultrasonic sensor connector and engage the clamp.
![]() |
Engage the 2 claws.
![]() |
Install the front bumper assembly with the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
![]() |
Install the pin hold clip.
![]() |
Remove the applied protective tape on the front bumper assembly.
| 3. INSTALL COOL AIR INTAKE DUCT SEAL (for 2GR-FE) |
![]() |
Install the cool air intake duct seal with the 7 clips.
| 4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for HID Headlight) |
| 5. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT |
Prepare the vehicle:
![]() |
| 6. PREPARE FOR HEADLIGHT AIMING |
![]() |
Prepare the vehicle:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (height) x 4 m (13.1 ft.) (width)) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration.

![]() |
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
H Line (Headlight height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) headlights):
Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).
| 7. INSPECT HEADLIGHT AIMING |
Cover the headlight or disconnect the connector of the headlight/headlight ECU on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming inspection.
Start the engine.
Turn on the headlights and check if the cutoff line for each low beam matches the preferred cutoff line in the illustration.

Turn on the high beams and check if the center of intensity for each high beam matches the preferred center of the intensity in the illustration.

| 8. ADJUST HEADLIGHT AIMING |
Remove any covers necessary to access the headlight adjusters.
Adjust the aim vertically:

| *1 | Aiming Screw A |
Adjust the aim horizontally:

| *1 | Aiming Screw B |
Install any covers that were removed to access the headlight adjusters.
| 9. PREPARE VEHICLE FOR FOG LIGHT AIM ADJUSTMENT |
Prepare the vehicle:
| 10. PREPARE FOR FOG LIGHT AIMING |
![]() |
Prepare the vehicle:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.
Draw a vertical line down the center of screen (V line).
Set the screen as shown in the illustration.

![]() |
Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.
H Line (Fog light height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the low-beam fog lights.
V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
Draw two vertical lines so that they intersect the H line at each center mark.
| 11. INSPECT FOG LIGHT AIMING |
Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.
Start the engine.
Turn on the fog light and check if the cut off line falls within the specified area in the following illustration.

| 12. ADJUST FOG LIGHT AIMING |
![]() |
Adjust the aim vertically:
Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.