POWER STEERING LINK > INSTALLATION |
| 1. INSTALL POWER STEERING RACK HOUSING HEAT INSULATOR (for 2GR-FE LHD) |
![]() |
Install the power steering rack housing heat insulator to the power steering link assembly.
| 2. INSTALL POWER STEERING RACK HOUSING HEAT INSULATOR (for 2GR-FE RHD) |
![]() |
Install the power steering rack housing heat insulator to the power steering link assembly with the bolt.
| 3. INSTALL POWER STEERING LINK ASSEMBLY |
![]() |
Install the power steering link assembly with the 2 bolts and 2 nuts.
| 4. CONNECT PRESSURE FEED TUBE ASSEMBLY (for LHD) |
![]() |
Temporarily connect the pressure feed tube assembly to the power steering link assembly.
![]() |
Install the pressure feed tube assembly clamp with the 2 bolts.
![]() |
Using SST, tighten the pressure feed tube assembly (pressure feed tube side).
![]() |
Using SST, tighten the pressure feed tube assembly (return tube side).
| 5. CONNECT PRESSURE FEED TUBE ASSEMBLY (for 2AZ-FE RHD) |
![]() |
Install the pressure feed tube assembly clamp with the bolt.
![]() |
Using SST, connect the pressure feed tube assembly to the power steering link assembly.
| 6. INSTALL RETURN TUBE ASSEMBLY (for 2AZ-FE RHD) |
![]() |
Using SST, install the return tube assembly to the power steering link assembly.
| 7. CONNECT STEERING GEAR OUTLET RETURN TUBE (for 2AZ-FE RHD) |
![]() |
Connect the steering gear outlet return tube to the return tube assembly with the clip.
| 8. CONNECT PRESSURE FEED TUBE ASSEMBLY (for 2GR-FE RHD) |
![]() |
Install the pressure feed tube assembly clamp with the bolt.
![]() |
Using SST, connect the pressure feed tube assembly to the power steering link assembly.
| 9. INSTALL RETURN TUBE ASSEMBLY (for 2GR-FE RHD) |
![]() |
Using SST, install the return tube assembly to the power steering link assembly.
| 10. CONNECT STEERING GEAR OUTLET RETURN TUBE (for 2GR-FE RHD) |
![]() |
Connect the steering gear outlet return tube to the return tube assembly with the clip.
| 11. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
| 12. CONNECT TIE ROD ASSEMBLY LH |
Connect the tie rod assembly LH to the steering knuckle with the nut.
Install a new cotter pin.
| 13. CONNECT TIE ROD ASSEMBLY RH |
| 14. CONNECT STEERING SLIDING YOKE |
![]() |
Align the matchmarks on the steering sliding yoke and the steering link assembly.
![]() |
Install the bolt.
| 15. INSTALL FRONT WHEELS |
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 17. BLEED POWER STEERING FLUID |
Check the fluid level .
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the steering wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine.
Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the steering wheel left or right to the full lock position and keep it in that position for 2 to 3 seconds, then turn the steering wheel to the opposite full lock position and keep it there for 2 to 3 seconds.
Repeat this procedure several times.
Stop the engine.
![]() |
Check for foaming or emulsification.
Check the fluid level .
| 18. CHECK POWER STEERING FLUID LEVEL |
Keep the vehicle level.
![]() |
With the engine stopped, check the fluid level in the fluid reservoir.
If necessary, add fluid.
Start the engine and run it at idle.
Turn the steering wheel from lock to lock several times to raise fluid temperature.
![]() |
Check for foaming or emulsification.
If foaming or emulsification is identified, bleed the power steering system .
![]() |
With the engine idling, measure the fluid level in the fluid reservoir.
Stop the engine.
Wait a few minutes and remeasure the fluid level in the fluid reservoir.
Check the fluid level.
| 19. CHECK FOR POWER STEERING FLUID LEAKAGE |
| 20. CHECK FOR EXHAUST GAS LEAKS |
| 21. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 22. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |