Home › STEERING › POWER STEERING › POWER STEERING LINK

POWER STEERING LINK > DISASSEMBLY

for Preparation Click here



1. SECURE POWER STEERING LINK ASSEMBLY


    C132044E01
  1. Using SST, secure the power steering link assembly.

    SST
    09612-00012  

    HINT:
    Tape the SST before use.



2. REMOVE STEERING LEFT TURN PRESSURE TUBE


    C132046E01
  1. Using SST, remove the steering left turn pressure tube.

    SST
    09023-38201  

  1. Remove the 2 O-rings from the steering left turn pressure tube.



3. REMOVE STEERING RIGHT TURN PRESSURE TUBE


    C132047E01
  1. Using SST, remove the steering right turn pressure tube.

    SST
    09023-38201  

  1. Remove the 2 O-rings from the steering right turn pressure tube.



4. REMOVE TIE ROD ASSEMBLY LH


    C132045E01
  1. Put matchmarks on the tie rod assembly LH and the steering rack end sub-assembly.

  1. Loosen the lock nut, and remove the tie rod assembly LH and the lock nut.



5. REMOVE TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



6. REMOVE STEERING RACK BOOT CLIP
  1. Using pliers, remove the RH and LH steering rack boot clips.



7. REMOVE NO. 2 STEERING RACK BOOT CLAMP


    C132048
  1. Using pliers, remove the RH and LH No. 2 steering rack boot clamps as shown in the illustration.

    NOTICE:
    Be careful not to damage the No. 2 steering rack boot.



8. REMOVE NO. 2 STEERING RACK BOOT
  1. Remove the No. 2 steering rack boot.



9. REMOVE NO. 1 STEERING RACK BOOT
  1. Remove the No. 1 steering rack boot.



10. REMOVE STEERING RACK END SUB-ASSEMBLY


    C132049
  1. Using a screwdriver and a hammer, unstake the RH and LH claw washers.

    NOTICE:
    Avoid any impact to the steering rack.



    C132050E01
  1. Using SST, remove the steering rack end sub-assembly (RH side) and the claw washer.

    SST
    09922-10010  

    NOTICE:
    Use SST 09922-10010 as shown in the illustration.



    C132051E01
  1. Using SST, remove the steering rack end sub-assembly (LH side) and the claw washer.

    SST
    09922-10010  

    NOTICE:
    Use SST 09922-10010 as shown in the illustration.

    HINT:
    Using SST, hold the rack and remove the steering rack end sub-assembly.



11. REMOVE RACK GUIDE


    C132052E01
  1. Using a straight hexagon wrench (24 mm (0.94 in.)), remove the rack guide spring cap.



    C132054
  1. Remove the compression spring and the rack guide sub-assembly.



    C132055
  1. Remove the rack guide base from the rack guide.



    C139140E01
  1. Remove the O-ring from the rack guide spring cap.



12. REMOVE DUST COVER


    C132058E01
  1. Wrap protective tape around the spline of the control valve in order to prevent damaging the dust cover.

  1. Remove the dust cover.



13. REMOVE POWER STEERING CONTROL VALVE ASSEMBLY


    C132056E01
  1. Using a socket wrench (27 mm (1.06 in.)), remove the rack housing cap.



    C132057E01
  1. Using SST, hold the control valve shaft and remove the nut.

    SST
    09616-00011  



    C132318
  1. Remove the 2 bolts and the power steering control valve assembly.

  1. Remove the gasket.



14. REMOVE POWER STEERING CONTROL VALVE SUB-ASSEMBLY


    C132319
  1. Using a press, remove the power steering control valve sub-assembly.



15. REMOVE POWER STEERING CONTROL VALVE LOWER OIL SEAL


    C132320
  1. Remove the power steering control valve lower oil seal from the power steering control valve sub-assembly.



16. REMOVE POWER STEERING CONTROL VALVE SPACER


    C132321E01
  1. Using a screwdriver, remove the 4 power steering control valve spacers from the power steering control valve sub-assembly.

    NOTICE:
    Be careful not to damage the spacer grooves on the control valve.

    HINT:
    Tape the screwdriver tip before use.



17. REMOVE POWER STEERING CONTROL VALVE UPPER OIL SEAL


    C132515E01
  1. Using SST and a press, press out the power steering control valve upper oil seal and the power steering control valve upper bearing from the control valve housing sub-assembly.

    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00250, 09951-00180, 09952-06010)



18. REMOVE CYLINDER END STOPPER HOLE SNAP RING


    C140649
  1. Using needle-nose pliers, remove the cylinder end stopper hole snap ring from the power steering rack housing.



19. REMOVE POWER STEERING RACK SUB-ASSEMBLY
  1. Remove the power steering rack sub-assembly with the cylinder end stopper and power steering rack bushing.



20. REMOVE CYLINDER END STOPPER


    C132323E01
  1. Remove the cylinder end stopper from the power steering rack sub-assembly.



21. REMOVE POWER STEERING RACK BUSHING


    C132324E01
  1. Remove the power steering rack bushing from the power steering rack sub-assembly.



    C132325E01
  1. Using a screwdriver, remove the O-ring from the power steering rack bushing.

    HINT:
    Tape the screwdriver tip before use.



    C132510E01
  1. Using SST, remove the rack bushing oil seal from the power steering rack bushing.

    SST
    09527-21011  
    09612-24014   (09613-22011)

    NOTICE:
    Be careful not to drop the power steering rack bushing.



22. REMOVE POWER STEERING CYLINDER TUBE OIL SEAL


    C132511E01
  1. Using SST and a press, remove the power steering cylinder tube oil seal.

    SST
    09950-70010   (09951-07360)
    09950-60010   (09951-00290, 09951-00250)

    NOTICE:
    Be careful not to damage the inside surface of the power steering rack housing.



23. REMOVE POWER PISTON OIL SEAL


    C132326E01
  1. Using a screwdriver, remove the power piston oil seal and the O-ring from the power steering rack.

    NOTICE:
    Be careful not to damage the oil seal groove on the power steering rack.

    HINT:
    Tape the screwdriver tip before use.