WIPER AND WASHER SYSTEM > TERMINALS OF ECU |
| CHECK WINDSHIELD WIPER RELAY ASSEMBLY (AUTO WIPER RELAY) |

Disconnect the E26 relay connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| W (E26-4) - Body ground | GR - Body ground | Front washer switch circuit | Front washer switch is ON | Below 1 Ω |
| Front washer switch is OFF | 10 kΩ or higher | |||
| IG (E26-12) - Body ground | L - Body ground | IG signal circuit | Ignition switch ON | 10 to 14 V |
| Ignition switch OFF | Below 1 V | |||
| WIG (E26-23) - Body ground | B - Body ground | WIG signal circuit | Ignition switch ON | 10 to 14 V |
| Ignition switch OFF | Below 1 V | |||
| E (E26-26) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the E26 relay connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| +2S (E26-1) - Body ground | P - Body ground | Front wiper LO speed signal circuit | Ignition switch ON, front wiper switch LO | 10 to 14 V |
| Ignition switch ON, front wiper switch except LO | Below 1 V | |||
| +1 (E26-2) - Body ground | R - Body ground | Front wiper motor LO speed signal circuit | Front wiper motor is in LO operation | 10 to 14 V |
| Front wiper motor is OFF | Below 1 V | |||
| +2 (E26-3) - Body ground | V - Body ground | Front wiper motor HI speed signal circuit | Front wiper motor is in HI operation | 10 to 14 V |
| Front wiper motor is OFF | Below 1 V | |||
| W (E26-4) - Body ground | GR - Body ground | Front washer motor circuit | Front washer switch is ON | Below 1 V |
| Front washer switch is OFF | 10 to 14 V | |||
| +SM (E26-10) - Body ground | Y- Body ground | Front wiper motor operation signal | Front wiper motor is in LO or HI operation | 10 to 14 V |
| Front wiper motor is OFF | Below 1 V | |||
| C1 (E26-17) - C0 (E26-16) | P - R | IG signal circuit | Ignition switch ON | 10 to 14 V |
| Ignition switch OFF | Below 1 V |
| CHECK HEADLIGHT CLEANER CONTROL RELAY |

Disconnect the A39 relay connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IG (A39-3) - Body ground | GR - Body ground | IG signal circuit | Ignition switch ON | 10 to 14 V |
| Ignition switch OFF | Below 1 V | |||
| E (A39-4) - Body ground | BR - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the A39 relay connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| HDLO (A39-1) - Body ground | P - Body ground | Headlight LO signal | Headlight control switch LO | Below 1 V |
| Headlight control switch except LO | 10 to 14 V | |||
| H (A39-2) - Body ground | Y - Body ground | Headlight cleaner switch signal | Headlight cleaner switch ON, headlight control switch LO | Below 1 V |
| Headlight cleaner switch ON, headlight control switch except LO | 10 to 14 V | |||
| FRWA (A39-5) - Body ground | L - Body ground | Front washer motor operation signal | Front washer switch is ON | Below 1 V |
| Front washer switch is OFF | 10 to 14 V | |||
| PB (A39-6) - Body ground | W - Body ground | Headlight cleaner motor signal | Headlight cleaner switch ON, headlight control switch except LO | 10 to 14 V |
| Headlight cleaner switch ON, headlight control switch LO | Below 1 V |