Home › BODY ELECTRICAL › LIGHTING › TURN SIGNAL FLASHER ASSEMBLY

TURN SIGNAL FLASHER ASSEMBLY > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT TURN SIGNAL FLASHER ASSEMBLY


    E068703E11
  1. Disconnect the E14 turn signal flasher assembly connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E14-1 (IG) - Body ground
    Ignition switch off
    Below 1 V
    E14-1 (IG) - Body ground
    Ignition switch ON
    10 to 14 V
    E14-4 (B) - Body ground
    Always
    10 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E14-5 (EL) - Body ground
    Turn signal switch OFF
    10 kΩ or higher
    E14-5 (EL) - Body ground
    Turn signal switch in LH position
    Below 1 Ω
    E14-6 (ER) - Body ground
    Turn signal switch OFF
    10 kΩ or higher
    E14-6 (ER) - Body ground
    Turn signal switch in RH position
    Below 1 Ω
    E14-7 (E) - Body ground
    Always
    Below 1 Ω
    E14-8 (HAZ) - Body ground
    Hazard warning switch OFF
    10 kΩ or higher
    E14-8 (HAZ) - Body ground
    Hazard warning switch ON
    Below 1 Ω

    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Reconnect the turn signal flasher assembly connector.

  1. Measure the voltage according to the valve(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E14-2 (LR) - Body ground
    Hazard warning switch OFF
    Below 1 V
    E14-2 (LR) - Body ground
    Hazard warning switch ON
    10 to 14 V (60 to 120 times per minute)
    E14-2 (LR) - Body ground
    Turn signal switch OFF
    Below 1 V
    E14-2 (LR) - Body ground
    Ignition switch ON and turn signal switch in RH position
    10 to 14 V (60 to 120 times per minute)
    E14-3 (LL) - Body ground
    Hazard warning switch OFF
    Below 1 V
    E14-3 (LL) - Body ground
    Hazard warning switch ON
    10 to 14 V (60 to 120 times per minute)
    E14-3 (LL) - Body ground
    Turn signal switch OFF
    Below 1 V
    E14-3 (LL) - Body ground
    Ignition switch ON and turn signal switch in LH position
    10 to 14 V (60 to 120 times per minute)
    E14-5 (EL) - Body ground
    Ignition switch ON and turn signal switch OFF
    10 to 14 V
    E14-5 (EL) - Body ground
    Ignition switch ON and turn signal switch in LH position
    Below 1 V
    E14-6 (ER) - Body ground
    Ignition switch ON and turn signal switch OFF
    10 to 14 V
    E14-6 (ER) - Body ground
    Ignition switch ON and turn signal switch in RH position
    Below 1 V
    E14-8 (HAZ) - Body ground
    Hazard warning switch OFF
    10 to 14 V
    E14-8 (HAZ) - Body ground
    Hazard warning switch ON
    Below 1 V

    If the result is not as specified, replace the turn signal flasher assembly.