SFI SYSTEM > TERMINALS OF ECM |
| SFI SYSTEM |

| Symbols (Terminal No.) | Wiring Colors | Terminal Descriptions | Conditions | STD Voltages |
| +B (A24-2) - E1 (C58-81) | R - W-B | Power source of ECM | Ignition switch on | 9 to 14 V |
| +B2 (A24-1) - E1 (C58-81) | R - W-B | Power source of ECM | Ignition switch on | 9 to 14 V |
| BATT (A24-20) - E1 (C58-81) | Y - W-B | Battery (for measuring the battery voltage and for the ECM memory) | Always | 9 to 14 V |
| +BM (A24-3) - E1 (C58-81) | LG - W-B | Power source of ETCS throttle motor | Always | 9 to 14 V |
| MREL (A24-44) - E1 (C58-81) | O - W-B | EFI relay operation signal | Ignition switch on | 9 to 14 V |
| IGSW (A24-28) - E1 (C58-81) | Y - W-B | Ignition switch signal | Ignition switch on | 9 to 14 V |
| FC (A24-7) - E1 (C58-81) | Y - W-B | C/OPEN relay operation signal (fuel pump control) | Ignition switch on | 9 to 14 V |
| STP ( A24-36 ) - E1 (C58-81) | W - W-B | Stop light switch signal | W-Bake pedal depressed | 7.5 to 14 V |
| STP (A24-36) - E1 C58-81) | W - W-B | Stop light switch signal | W-Bake pedal released | Below 1.5 V |
| ST1- (A24-35) - E1 (C58-81) | GR - W-B | Stop light switch signal (opposite to STP terminal) | Ignition switch on, W-Bake pedal depressed | Below 1.5 V |
| ST1- (A24-35) - E1 (C58-81) | GR - W-B | Stop light switch signal (opposite to STP terminal) | Ignition switch on, W-Bake pedal released | 7.5 to 14 V |
| VPA (A24-55) - E1 (C58-81) | G - W-B | Accelerator pedal position sensor signal (for engine control) | Ignition switch on, Accelerator pedal fully released | 0.5 to 1.1 V |
| VPA (A24-55) - E1 (C58-81) | G - W-B | Accelerator pedal position sensor signal (for engine control) | Ignition switch on, Accelerator pedal fully depressed | 2.6 to 4.5 V |
| VPA2 (A24-56) - EPA2 (A24-60) | R - O | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully released | 1.2 to 2.0 V |
| VPA2 (A55-56) - EPA2 (A24-60) | R - O | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully depressed | 3.4 to 5.0 V |
| EPA (A5-59) - VPA (A24-55) | Y - G | Accelerator pedal position sensor signal (for engine control) | Ignition switch on, Accelerator pedal fully released | 0.5 to 1.1 V |
| EPA (A5-59) - VPA (A24-55) | Y - G | Accelerator pedal position sensor signal (for engine control) | Ignition switch on, Accelerator pedal fully depressed | 2.6 to 4.5 V |
| EPA2 (A24-60) - VPA2 (A24-56) | O - R | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully released | 1.2 to 2.0 V |
| EPA2 (A24-60) - VPA2 (A24-56) | O - R | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully depressed | 3.4 to 5.0 V |
| TC (A24-27) - E1 (C58-81) | P - W-B | Terminal TC of DLC3 | Ignition switch on | 9 to 14 V |
| VCPA (A24-57) - EPA (A24-59) | B - Y | Power source of accelerator pedal position sensor (for VPA) | Ignition switch on | 4.5 to 5.0 V |
| VCP2 (A24-58) - EPA2 (A24-60) | L - O | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch on | 4.5 to 5.0 V |
| TACH (A24-15) - E1 (C58-81) | B - W-B | Engine speed signal (for combination meter) | Idling | Pulse generation (see waveform 11) |
| CCS (A24-40) - E1 (C58-81) | W - W-B | Cruise control main switch signal | Ignition switch on CANCEL switch ON SET/COAST switch ON RES/ACC switch ON Main switch ON | 10 to 16 V 6.6 to 10.1 V 4.5 to 7.1 V 2.3 to 4.0 V Below 1 V |
| SPD (A24-8) - E1 (C58-81) | V - W-B | Vehicle speed signal from combination meter | Ignition switch on, Rotate driving wheel slowly | Pulse generation (see waveform 8) |
| W (A24-24) - E1 (C58-81) | BR - W-B | Malfunction Indicator Lamp (MIL) operation signal | Ignition switch on | Below 3.0 V |
| W (A24-24) - E1 (C58-81) | BR - W-B | Malfunction Indicator Lamp (MIL) operation signal | Idling | 9 to 14 V |
| CANH (A24-41) - E1 (C58-81) | B - W-B | CAN communication line | Ignition switch on | Pulse generation (see waveform 12) |
| CANL (A24-49) - E1 (C58-81) | W - W-B | CAN communication line | Ignition switch on | Pulse generation (see waveform 13) |
| E1 (C58-81) - Body ground | W-B - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| #10 (C58-45) - E01 (C58-22) #20 (C58-85) - E01 (C58-22) #30 (C58-44) - E01 (C58-22) #40 (C58-84) - E01 (C58-22) #50 (C58-43) - E01 (C58-22) #60 (C58-83) - E01 (C58-22) | B - W-B R - W-B Y - W-B L - W-B W-L - W-B BR - W-B | Fuel injector operation signal | Ignition switch on | 9 to 14 V |
| #10 (C58-45) - E01 (C58-22) #20 (C58-85) - E01 (C58-22) #30 (C58-44) - E01 (C58-22) #40 (C58-84) - E01 (C58-22) #50 (C58-43) - E01 (C58-22) #60 (C58-83) - E01 (C58-22) | B - W-B R - W-B Y - W-B L - W-B W-L - W-B BR - W-B | Fuel injector operation signal | Idling | Pulse generation (see waveform 3) |
| PSW (C58-70) - E1 (C58-81) | B - W-B | P/S pressure switch signal | Ignition switch on | 9 to 14 V |
| STA (A24-48) - E1 (C58-81) | V - W-B | Starter relay operation signal | Cranking | 9 to 14 V |
| OC2- (C58-51) - OC2+ (C58-52) | R - BR | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on | Pulse generation (see waveform 1) |
| OC2+ (C58-52) - OC2- (C58-51) | BR - R | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on | Pulse generation (see waveform 1) |
| OC1- (C58-57) - OC1+ (C58-58) | B - W | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on | Pulse generation (see waveform 1) |
| OC1+ (C58-58) - OC1- (C58-57) | W - B | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on | Pulse generation (see waveform 1) |
| VV2+ (C58-67) - VV2- (C58-90) | W - B | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| VV1+ (C58-69) - VV1- (C58-92) | L - LG | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| NE- (C58-111) - NE+ (C58-110) | R - G | Crankshaft position sensor signal | Idling | Pulse generation (see waveform 5) |
| NE+ (C58-110) - NE- (C58-111) | G - R | Crankshaft position sensor signal | Idling | Pulse generation (see waveform 5) |
| EV2- (C58-89) - EV2+ (C58-66) | L - G-R | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| EV2+ (C58-66) - EV2- (C58-89) | G-R - L | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| EV1- (C58-91) - EV1+ (C58-68) | B - Y | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| EV1+ (C58-68) - EV1- (C58-91) | Y - B | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| OE1+ (C58-16) - OE1- (C58-17) | L - LG | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on | Pulse generation (see waveform 1) |
| OE2+ (C58-14) - OE2- (C58-15) | W-L - Y | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on | Pulse generation (see waveform 1) |
| VV2- (C58-90) - VV2+ (C58-67) | B - W | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| VV1- (C58-92) - VV1+ (C58-69) | LG - L | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| OE1- (C58-17) - OE1+ (C58-16) | LG - L | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on | Pulse generation (see waveform 1) |
| OE2- (C58-15) - OE2+ (C58-14) | Y - W-L | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on | Pulse generation (see waveform 1) |
| HT1B (C58-48) - E1 (C58-81) HT2B (C58-47) - E1 (C58-81) | LG - W-B Y - W-B | Heated oxygen sensor heater operation signal | Idling | Below 3.0 V |
| HT1B (C58-48) - E1 (C58-81) HT2B (C58-47) - E1 (C58-81) | LG - W-B Y - W-B | Heated oxygen sensor heater operation signal | Ignition switch on | 9 to 14 V |
| ACM (C58-42) - E1 (C58-81) | L-B - W-B | VSV for active control mount system operation signal | Ignition switch on | 9 to 14 V |
| M- (C58-18) - ME01 (C58-20) | R - B | Throttle drive motor operation signal (negative terminal) | Idling with warm engine | Pulse generation (see waveform 10) |
| M+ (C58-19) - ME01 (C58-20) | G - B | Throttle drive motor operation signal (positive terminal) | Idling with warm engine | Pulse generation (see waveform 9) |
| E02 (C58-21) - Body ground | B-W - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| E01 (C58-22) - Body ground | W-B - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| IGT1 (C58-40) - E1 (C58-81) IGT2 (C58-39) - E1 (C58-81) IGT3 (C58-38) - E1 (C58-81) IGT4 (C58-37) - E1 (C58-81) IGT5 (C58-36) - E1 (C58-81) IGT6 (C58-35) - E1 (C58-81) | W - W-B G-R - W-B G - W-B LG - W-B P - W-B L-B - W-B | Ignition coil with igniter (ignition signal) | Idling | Pulse generation (see waveform 6) |
| GE01 (C58-41) - E1 (C58-81) | G-R - W-B | Shielded earth (ground) circuit of throttle drive motor | Always | Below 1 V |
| OX1B (C58-88) - EX1B (C58-65) OX2B (C58-87) - EX2B (C58-64) | W - BR B - W-B | Heated oxygen sensor signal | With engine speed at 2,500 rpm for 2 minutes after warming up | Pulse generation (see waveform 2) |
| VTA2 (C58-99) - ETA (C58-97) | W-L - P | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully released | 2.1 to 3.1 V |
| VTA2 (C58-99) - ETA (C58-97) | W-L - P | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully depressed | 4.5 to 5.0 V |
| VTA1 (C58-98) - ETA (C58-97) | Y - P | Throttle position sensor signal (for engine control) | Ignition switch on, Throttle valve fully closed | 0.5 to 1.2 V |
| VTA1 (C58-98) - ETA (C58-97) | Y - P | Throttle position sensor signal (for engine control) | Ignition switch on, Throttle valve fully open | 3.2 to 4.8 V |
| THW (C58-79) - ETHW (C58-78) | B - P | Engine coolant temperature sensor signal | Idling, Engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| THA (C58-71) - ETHA (C58-74) | P - G-R | Intake air temperature sensor signal | Idling, Intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| IGF1 (C58-106) - E1 (C58-81) | BR - W-B | Ignition coil with igniter (ignition confirmation signal) | Ignition switch on | 4.5 to 5.0 V |
| IGF1 (C58-106) - E1 (C58-81) | BR - W-B | Ignition coil with igniter (ignition confirmation signal) | Idling | Pulse generation (see waveform 6) |
| AICV (A24-4) - E1 (C58-81) | V - W-B | VSV for Air intake control system operation signal | Ignition switch on | 9 to 14 V |
| E2G (C58-73) - E1 (C58-81) | LG - W-B | Earth (ground) circuit of sensor for mass air flow meter | Always | Below 1 V |
| VG (C58-72) - E2G (C58-73) | L-B - LG | Mass Air Flow (MAF) meter signal | Idling, Shift lever position P or N, A/C switch OFF | 0.5 to 3.0 V |
| ACIS (C58-107) - E1 (C58-81) | B-W - W-B | VSV for ACIS (Acoustic Control Induction System) operation signal | Ignition switch on | 9 to 14 V |
| PRG (C58-108) - E1 (C58-81) | G-R - W-B | Purge VSV for EVAP system operation signal | Ignition switch on | 9 to 14 V |
| PRG (C58-108) - E1 (C58-81) | G-R - W-B | Purge VSV for EVAP system operation signal | Idling | Pulse generation (see waveform 7) |
| HA2A (C58-109) - E05 (C58-46) | B-W - W | A/F sensor heater operation signal | Idling | Below 3.0 V |
| HA2A (C58-109) - E05 (C58-46) | B-W - W | A/F sensor heater operation signal | Ignition switch on | 9 to 14 V |
| HA1A (C58-86) - E04 (C58-23) | G - W | A/F sensor heater operation signal | Idling | Below 3.0 V |
| HA1A (C58-86) - E04 (C58-23) | G - W | A/F sensor heater operation signal | Ignition switch on | 9 to 14 V |
| ME01 (C58-20) - E1 (C58-81) | B - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| E03 (C58-104) - E1 (C58-81) | B - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| HT2B (C58-47) - E1 (C58-81) HT1B (C58-48) - E1 (C58-81) | Y - W-B LG - W-B | Heated oxygen sensor heater operation signal | Idling | Below 3.0 V |
| HT2B (C58-47) - E1 (C58-81) HT1B (C58-48) - E1 (C58-81) | Y - W-B LG - W-B | Heated oxygen sensor heater operation signal | Ignition switch on | 9 to 14 V |
| E05 (C58-46) - E1 (C58-81) | W - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| E04 (C58-23) - E1 (C58-81) | W - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| EKN2 (C58-117) - KNK2 (C58-118) | W - B | Earth (ground) circuit of knock sensor | With engine speed at 4,000 rpm after warming up | Pulse generation (see waveform 4) |
| KNK2 (C58-118) - EKN2 (C58-117) | B - W | Knock sensor signal | With engine speed at 4,000 rpm after warming up | Pulse generation (see waveform 4) |
| A1A+ (C58-93) - E1 (C58-81) | L - W-B | A/F sensor signal | Ignition switch on | 3.3 V*1
|
| A1A+ (C58-93) - E1 (C58-81) | L - W-B | A/F sensor signal | Ignition switch on | 3.0 V*1
|
| A2A+ (C58-120) - E1 (C58-81) | BR - W-B | A/F sensor signal | Ignition switch on | 3.3 V*1
|
| A2A+ (C58-120) - E1 (C58-81) | BR - W-B | A/F sensor signal | Ignition switch on | 3.0 V*1
|
| EKNK (C58-94) - KNK1 (C58-95) | G - R | Earth (ground) circuit of knock sensor | With engine speed at 4,000 rpm after warming up | Pulse generation (see waveform 4) |
| KNK1 (C58-95) - EKNK (C58-94) | R - G | Knock sensor signal | With engine speed at 4,000 rpm after warming up | Pulse generation (see waveform 4) |
| A1A- (C58-116) - E1 (C58-81) | P - W-B | A/F sensor | Ignition switch on | 3.3 V*1
|
| A1A- (C58-116) - E1 (C58-81) | P - W-B | A/F sensor | Ignition switch on | 3.0 V*1
|
| A2A- (C58-119) - E1 (C58-81) | Y - W-B | A/F sensor | Ignition switch on | 3.3 V*1
|
| A2A- (C58-119) - E1 (C58-81) | Y - W-B | A/F sensor | Ignition switch on | 3.0 V*1
|
| OX2B (C58-87) - EX2B (C58-64) OX1B (C58-88) - EX1B (C58-65) | B - W-B W - BR | Heated oxygen sensor signal | With engine speed at 2,500 rpm for 2 minutes after warming up | Pulse generation (see waveform 2) |
| P (C58-24) - E1 (C58-81) | B-W - W-B | P shift position switch signal | Ignition switch on and shift lever P position | 9 to 14 V |
| P (C58-24) - E1 (C58-81) | B-W - W-B | P shift position switch signal | Ignition switch on and shift lever except P position | Below 1 V |
| R (C58-25) - E1 (C58-81) | P - W-B | R shift position switch signal | Ignition switch on and shift lever R position | 9 to 14 V |
| R (C58-25) - E1 (C58-81) | P - W-B | R shift position switch signal | Ignition switch on and shift lever except R position | Below 1 V |
| N (C58-27) - E1 (C58-81) | L-B - W-B | N shift position switch signal | Ignition switch on and shift lever N position | 9 to 14 V |
| N (C58-27) - E1 (C58-81) | L-B - W-B | N shift position switch signal | Ignition switch on and shift lever except N position | Below 1 V |
| D (C58-26) - E1 (C58-81) | G - W-B | D shift position switch signal | Ignition switch on and shift lever D position | 9 to 14 V |
| D (C58-26) - E1 (C58-81) | G - W-B | D shift position switch signal | Ignition switch on and shift lever except D position | Below 1 V |
| S (A24-25) - E1 (C58-81) | Y - W-B | S shift position switch signal | Ignition switch on and shift lever S position | 9 to 14 V |
| S (A24-25) - E1 (C58-81) | Y - W-B | S shift position switch signal | Ignition switch on and shift lever except S position | Below 1 V |
| SFTD (A24-51) - E1 (C58-81) | L - W-B | Down shift switch signal | Ignition switch on and shift lever S position | 9 to 14 V |
| SFTD (A24-51) - E1 (C58-81) | L - W-B | Down shift switch signal | Ignition switch on and shift lever "-" position (Down shift) | Below 1 V |
| SFTU (A24-16) - E1 (C58-81) | R - W-B | Up shift switch signal | Ignition switch on and shift lever S position | 9 to 14 V |
| SFTU (A24-16) - E1 (C58-81) | R - W-B | Up shift switch signal | Ignition switch on and shift lever "+" position (Up shift) | Below 1 V |
| Symbols (Terminal No.) | Wiring Colors | Terminal Descriptions | Conditions | STD Voltages |
| +B (A55-2) - E1 (C55-81) | R - W-B | Power source of ECM | Ignition switch on | 9 to 14 V |
| +B2 (A55-1) - E1 (C55-81) | R - W-B | Power source of ECM | Ignition switch on | 9 to 14 V |
| BATT (A55-20) - E1 (C55-81) | Y - W-B | Battery (for measuring the battery voltage and for the ECM memory) | Always | 9 to 14 V |
| +BM (A55-3) - E1 (C55-81) | LG - W-B | Power source of ETCS throttle motor | Always | 9 to 14 V |
| MREL (A55-44) - E1 (C55-81) | O - W-B | EFI relay operation signal | Ignition switch on | 9 to 14 V |
| IGSW (A55-28) - E1 (C55-81) | Y - W-B | Ignition switch signal | Ignition switch on | 9 to 14 V |
| FC (A55-7) - E1 (C55-81) | Y - W-B | C/OPEN relay operation signal (fuel pump control) | Ignition switch on | 9 to 14 V |
| STP ( A55-36 ) - E1 (C55-81) | W - W-B | Stop light switch signal | Brake pedal depressed | 7.5 to 14 V |
| STP (A55-36) - E1 C55-81) | W - W-B | Stop light switch signal | Brake pedal released | Below 1.5 V |
| ST1- (A55-35) - E1 (C55-81) | GR - W-B | Stop light switch signal (opposite to STP terminal) | Ignition switch on, Brake pedal depressed | Below 1.5 V |
| ST1- (A55-35) - E1 (C55-81) | GR - W-B | Stop light switch signal (opposite to STP terminal) | Ignition switch on, Brake pedal released | 7.5 to 14 V |
| VPA (A55-55) - E1 (C55-81) | G - W-B | Accelerator pedal position sensor signal (for engine control) | Ignition switch on, Accelerator pedal fully released | 0.5 to 1.1 V |
| VPA (A55-55) - E1 (C55-81) | G - W-B | Accelerator pedal position sensor signal (for engine control) | Ignition switch on, Accelerator pedal fully depressed | 2.6 to 4.5 V |
| VPA2 (A55-56) - EPA2 (A55-60) | R - O | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully released | 1.2 to 2.0 V |
| VPA2 (A55-56) - EPA2 (A55-60) | R - O | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully depressed | 3.4 to 5.0 V |
| EPA (A5-59) - VPA (A55-55) | Y - G | Accelerator pedal position sensor signal (for engine control) | Ignition switch on, Accelerator pedal fully released | 0.5 to 1.1 V |
| EPA (A5-59) - VPA (A55-55) | Y - G | Accelerator pedal position sensor signal (for engine control) | Ignition switch on, Accelerator pedal fully depressed | 2.6 to 4.5 V |
| EPA2 (A55-60) - VPA2 (A55-56) | O - R | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully released | 1.2 to 2.0 V |
| EPA2 (A55-60) - VPA2 (A55-56) | O - R | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully depressed | 3.4 to 5.0 V |
| TC (A55-27) - E1 (C55-81) | P - W-B | Terminal TC of DLC3 | Ignition switch on | 9 to 14 V |
| VCPA (A55-57) - EPA (A55-59) | B - Y | Power source of accelerator pedal position sensor (for VPA) | Ignition switch on | 4.5 to 5.0 V |
| VCP2 (A55-58) - EPA2 (A55-60) | L - O | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch on | 4.5 to 5.0 V |
| TACH (A55-15) - E1 (C55-81) | B - W-B | Engine speed signal (for combination meter) | Idling | Pulse generation (see waveform 11) |
| CCS (A55-40) - E1 (C55-81) | W - W-B | Cruise control main switch signal | Ignition switch on CANCEL switch ON SET/COAST switch ON RES/ACC switch ON Main switch ON | 10 to 16 V 6.6 to 10.1 V 4.5 to 7.1 V 2.3 to 4.0 V Below 1 V |
| SPD (A55-8) - E1 (C55-81) | V - W-B | Vehicle speed signal from combination meter | Ignition switch on, Rotate driving wheel slowly | Pulse generation (see waveform 8) |
| W (A55-24) - E1 (C55-81) | BR - W-B | Malfunction Indicator Lamp (MIL) operation signal | Ignition switch on | Below 3.0 V |
| W (A55-24) - E1 (C55-81) | BR - W-B | Malfunction Indicator Lamp (MIL) operation signal | Idling | 9 to 14 V |
| CANH (A55-41) - E1 (C55-81) | B - W-B | CAN communication line | Ignition switch on | Pulse generation (see waveform 12) |
| CANL (A55-49) - E1 (C55-81) | W - W-B | CAN communication line | Ignition switch on | Pulse generation (see waveform 13) |
| E1 (C55-81) - Body ground | W-B - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| #10 (C55-45) - E01 (C55-22) #20 (C55-85) - E01 (C55-22) #30 (C55-44) - E01 (C55-22) #40 (C55-84) - E01 (C55-22) #50 (C55-43) - E01 (C55-22) #60 (C55-83) - E01 (C55-22) | B - W-B R - W-B Y - W-B L - W-B W-L - W-B BR - W-B | Fuel injector operation signal | Ignition switch on | 9 to 14 V |
| #10 (C55-45) - E01 (C55-22) #20 (C55-85) - E01 (C55-22) #30 (C55-44) - E01 (C55-22) #40 (C55-84) - E01 (C55-22) #50 (C55-43) - E01 (C55-22) #60 (C55-83) - E01 (C55-22) | B - W-B R - W-B Y - W-B L - W-B W-L - W-B BR - W-B | Fuel injector operation signal | Idling | Pulse generation (see waveform 3) |
| PSW (C55-70) - E1 (C55-81) | B - W-B | P/S pressure switch signal | Ignition switch on | 9 to 14 V |
| STA (A55-48) - E1 (C55-81) | V - W-B | Starter relay operation signal | Cranking | 9 to 14 V |
| OC2- (C55-51) - OC2+ (C55-52) | R - BR | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on | Pulse generation (see waveform 1) |
| OC2+ (C55-52) - OC2- (C55-51) | BR - R | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on | Pulse generation (see waveform 1) |
| OC1- (C55-57) - OC1+ (C55-58) | B - W | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on | Pulse generation (see waveform 1) |
| OC1+ (C55-58) - OC1- (C55-57) | W - B | Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) | Ignition switch on | Pulse generation (see waveform 1) |
| VV2+ (C55-67) - VV2- (C55-90) | W - B | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| VV1+ (C55-69) - VV1- (C55-92) | L - LG | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| NE- (C55-111) - NE+ (C55-110) | R - G | Crankshaft position sensor signal | Idling | Pulse generation (see waveform 5) |
| NE+ (C55-110) - NE- (C55-111) | G - R | Crankshaft position sensor signal | Idling | Pulse generation (see waveform 5) |
| EV2- (C55-89) - EV2+ (C55-66) | L - G-R | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| EV2+ (C55-66) - EV2- (C55-89) | G-R - L | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| EV1- (C55-91) - EV1+ (C55-68) | B - Y | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| EV1+ (C55-68) - EV1- (C55-91) | Y - B | Variable Valve Timing (VVT) sensor signal (Exhaust side) | Idling | Pulse generation (see waveform 5) |
| OE1+ (C55-16) - OE1- (C55-17) | L - LG | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on | Pulse generation (see waveform 1) |
| OE2+ (C55-14) - OE2- (C55-15) | W-L - Y | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on | Pulse generation (see waveform 1) |
| VV2- (C55-90) - VV2+ (C55-67) | B - W | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| VV1- (C55-92) - VV1+ (C55-69) | LG - L | Variable Valve Timing (VVT) sensor signal (Intake side) | Idling | Pulse generation (see waveform 5) |
| OE1- (C55-17) - OE1+ (C55-16) | LG - L | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on | Pulse generation (see waveform 1) |
| OE2- (C55-15) - OE2+ (C55-14) | Y - W-L | Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side) | Ignition switch on | Pulse generation (see waveform 1) |
| HT1B (C55-48) - E1 (C55-81) HT2B (C55-47) - E1 (C55-81) | LG - W-B Y - W-B | Heated oxygen sensor heater operation signal | Idling | Below 3.0 V |
| HT1B (C55-48) - E1 (C55-81) HT2B (C55-47) - E1 (C55-81) | LG - W-B Y - W-B | Heated oxygen sensor heater operation signal | Ignition switch on | 9 to 14 V |
| ACM (C55-42) - E1 (C55-81) | L-B - W-B | VSV for active control mount system operation signal | Ignition switch on | 9 to 14 V |
| M- (C55-18) - ME01 (C55-20) | R - B | Throttle drive motor operation signal (negative terminal) | Idling with warm engine | Pulse generation (see waveform 10) |
| M+ (C55-19) - ME01 (C55-20) | G - B | Throttle drive motor operation signal (positive terminal) | Idling with warm engine | Pulse generation (see waveform 9) |
| E02 (C55-21) - Body ground | B-W - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| E01 (C55-22) - Body ground | W-B - - | Earth (ground) circuit of ECM | Always | Below 1 V |
| IGT1 (C55-40) - E1 (C55-81) IGT2 (C55-39) - E1 (C55-81) IGT3 (C55-38) - E1 (C55-81) IGT4 (C55-37) - E1 (C55-81) IGT5 (C55-36) - E1 (C55-81) IGT6 (C55-35) - E1 (C55-81) | W - W-B G-R - W-B G - W-B LG - W-B P - W-B L-B - W-B | Ignition coil with igniter (ignition signal) | Idling | Pulse generation (see waveform 6) |
| GE01(C55-41) - E1 (C55-81) | G-R - W-B | Shielded earth (ground) circuit of throttle drive motor | Always | Below 1 V |
| OX1B (C55-88) - EX1B (C55-65) OX2B (C55-87) - EX2B (C55-64) | W - BR B - W-B | Heated oxygen sensor signal | With engine speed at 2,500 rpm for 2 minutes after warming up | Pulse generation (see waveform 2) |
| VTA2 (C55-99) - ETA (C55-97) | W-L - P | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully released | 2.1 to 3.1 V |
| VTA2 (C55-99) - ETA (C55-97) | W-L - P | Throttle position sensor signal (for sensor malfunction detection) | Ignition switch on, Accelerator pedal fully depressed | 4.5 to 5.0 V |
| VTA1 (C55-98) - ETA (C55-97) | Y - P | Throttle position sensor signal (for engine control) | Ignition switch on, Throttle valve fully closed | 0.5 to 1.2 V |
| VTA1 (C55-98) - ETA (C55-97) | Y - P | Throttle position sensor signal (for engine control) | Ignition switch on, Throttle valve fully open | 3.2 to 4.8 V |
| THW (C55-79) - ETHW (C55-78) | B - P | Engine coolant temperature sensor signal | Idling, Engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| THA (C55-71) - ETHA (C55-74) | P - G-R | Intake air temperature sensor signal | Idling, Intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| IGF1 (C55-106) - E1 (C55-81) | BR - W-B | Ignition coil with igniter (ignition confirmation signal) | Ignition switch on | 4.5 to 5.0 V |
| IGF1 (C55-106) - E1 (C55-81) | BR - W-B | Ignition coil with igniter (ignition confirmation signal) | Idling | Pulse generation (see waveform 6) |
| AICV (A55-4) - E1 (C55-81) | V - W-B | VSV for Air intake control system operation signal | Ignition switch on | 9 to 14 V |
| E2G (C55-73) - E1 (C55-81) | LG - W-B | Earth (ground) circuit of sensor for mass air flow meter | Always | Below 1 V |
| VG (C55-72) - E2G (C55-73) | L-B - LG | Mass Air Flow (MAF) meter signal | Idling, Shift lever position P or N, A/C switch OFF | 0.5 to 3.0 V |
| ACIS (C55-107) - E1 (C55-81) | B-W - W-B | VSV for ACIS (Acoustic Control Induction System) operation signal | Ignition switch on | 9 to 14 V |
| PRG (C55-108) - E1 (C55-81) | G-R - W-B | Purge VSV for EVAP system operation signal | Ignition switch on | 9 to 14 V |
| PRG (C55-108) - E1 (C55-81) | G-R - W-B | Purge VSV for EVAP system operation signal | Idling | Pulse generation (see waveform 7) |
| HA2A (C55-109) - E05 (C55-46) | B-W - W | A/F sensor heater operation signal | Idling | Below 3.0 V |
| HA2A (C55-109) - E05 (C55-46) | B-W - W | A/F sensor heater operation signal | Ignition switch on | 9 to 14 V |
| HA1A (C55-86) - E04 (C55-23) | G - W | A/F sensor heater operation signal | Idling | Below 3.0 V |
| HA1A (C55-86) - E04 (C55-23) | G - W | A/F sensor heater operation signal | Ignition switch on | 9 to 14 V |
| ME01 (C55-20) - E1 (C55-81) | B - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| E03 (C55-104) - E1 (C55-81) | B - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| HT2B (C55-47) - E1 (C55-81) HT1B (C55-48) - E1 (C55-81) | Y - W-B LG - W-B | Heated oxygen sensor heater operation signal | Idling | Below 3.0 V |
| HT2B (C55-47) - E1 (C55-81) HT1B (C55-48) - E1 (C55-81) | Y - W-B LG - W-B | Heated oxygen sensor heater operation signal | Ignition switch on | 9 to 14 V |
| E05 (C55-46) - E1 (C55-81) | W - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| E04 (C55-23) - E1 (C55-81) | W - W-B | Earth (ground) circuit of ECM | Always | Below 1 V |
| EKN2 (C55-117) - KNK2 (C55-118) | W - B | Earth (ground) circuit of knock sensor | With engine speed at 4,000 rpm after warming up | Pulse generation (see waveform 4) |
| KNK2 (C55-118) - EKN2 (C55-117) | B - W | Knock sensor signal | With engine speed at 4,000 rpm after warming up | Pulse generation (see waveform 4) |
| A1A+ (C55-93) - E1 (C55-81) | L - W-B | A/F sensor signal | Ignition switch on | 3.3 V*1
|
| A1A+ (C55-93) - E1 (C55-81) | L - W-B | A/F sensor signal | Ignition switch on | 3.0 V*1
|
| A2A+ (C55-120) - E1 (C55-81) | L - W-B | A/F sensor signal | Ignition switch on | 3.3 V*1
|
| A2A+ (C55-120) - E1 (C55-81) | L - W-B | A/F sensor signal | Ignition switch on | 3.0 V*1
|
| EKNK (C55-94) - KNK1 (C55-95) | G - R | Earth (ground) circuit of knock sensor | With engine speed at 4,000 rpm after warming up | Pulse generation (see waveform 4) |
| KNK1 (C55-95) - EKNK (C55-94) | R - G | Knock sensor signal | With engine speed at 4,000 rpm after warming up | Pulse generation (see waveform 4) |
| A1A- (C55-116) - E1 (C55-81) | P - W-B | A/F sensor | Ignition switch on | 3.3 V*1
|
| A1A- (C55-116) - E1 (C55-81) | P - W-B | A/F sensor | Ignition switch on | 3.0 V*1
|
| A2A- (C55-119) - E1 (C55-81) | Y - W-B | A/F sensor | Ignition switch on | 3.3 V*1
|
| A2A- (C55-119) - E1 (C55-81) | Y - W-B | A/F sensor | Ignition switch on | 3.0 V*1
|
| OX2B (C55-87) - EX2B (C55-64) OX1B (C55-88) - EX1B (C55-65) | B - W-B W - BR | Heated oxygen sensor signal | With engine speed at 2,500 rpm for 2 minutes after warming up | Pulse generation (see waveform 2) |
| P (C55-24) - E1 (C55-81) | B-W - W-B | P shift position switch signal | Ignition switch on and shift lever P position | 9 to 14 V |
| P (C55-24) - E1 (C55-81) | B-W - W-B | P shift position switch signal | Ignition switch on and shift lever except P position | Below 1 V |
| R (C55-25) - E1 (C55-81) | P - W-B | R shift position switch signal | Ignition switch on and shift lever R position | 9 to 14 V |
| R (C55-25) - E1 (C55-81) | P - W-B | R shift position switch signal | Ignition switch on and shift lever except R position | Below 1 V |
| N (C55-27) - E1 (C55-81) | L-B - W-B | N shift position switch signal | Ignition switch on and shift lever N position | 9 to 14 V |
| N (C55-27) - E1 (C55-81) | L-B - W-B | N shift position switch signal | Ignition switch on and shift lever except N position | Below 1 V |
| D (C55-26) - E1 (C55-81) | G - W-B | D shift position switch signal | Ignition switch on and shift lever D position | 9 to 14 V |
| D (C55-26) - E1 (C55-81) | G - W-B | D shift position switch signal | Ignition switch on and shift lever except D position | Below 1 V |
| S (A55-25) - E1 (C55-81) | Y - W-B | S shift position switch signal | Ignition switch on and shift lever S position | 9 to 14 V |
| S (A55-25) - E1 (C55-81) | Y - W-B | S shift position switch signal | Ignition switch on and shift lever except S position | Below 1 V |
| SFTD (A55-51) - E1 (C55-81) | L - W-B | Down shift switch signal | Ignition switch on and shift lever S position | 9 to 14 V |
| SFTD (A55-51) - E1 (C55-81) | L - W-B | Down shift switch signal | Ignition switch on and shift lever "-" position (Down shift) | Below 1 V |
| SFTU (A55-16) - E1 (C55-81) | R - W-B | Up shift switch signal | Ignition switch on and shift lever S position | 9 to 14 V |
| SFTU (A55-16) - E1 (C55-81) | R - W-B | Up shift switch signal | Ignition switch on and shift lever "+" position (Up shift) | Below 1 V |
![]() |
WAVEFORM 1
Camshaft timing Oil Control Valve (OCV) operation signal
| ECM Terminal Names | Between OC1+ and OC1- , OC2+ and OC2- , OE1+ and OE1- , or OE2+ and OE2- |
| Tester Ranges | 5 V/DIV., 1 ms./DIV. |
| Conditions | Idling |
![]() |
WAVEFORM 2
Heated oxygen sensor signal
| ECM Terminal Names | Between OX1B and EX1B, or OX2B and EX2B |
| Tester Ranges | 0.2 V/DIV., 200 ms./DIV. |
| Conditions | Engine speed is maintained at 2,500 rpm for 2 minutes after sensor is warmed up |
![]() |
WAVEFORM 3
Fuel injector operation signal
| ECM Terminal Names | Between #10 (to 60) and E01 |
| Tester Ranges | 30 V/DIV., 20 ms./DIV. |
| Conditions | Idling |
![]() |
WAVEFORM 4
Knock sensor signal
| ECM Terminal Names | Between KNK1 and EKNK, or KNK2 and EKN2 |
| Tester Ranges | 0.01 to 10 V/DIV., 0.01 to 10 ms./DIV. |
| Conditions | Engine speed is maintained at 4,000 rpm after engine is warmed up |
![]() |
WAVEFORM 5
Variable Valve Timing (VVT) sensor signal (1)
Crankshaft position sensor signal (2)
| ECM Terminal Names | (1) Between VV1+ and VV1- , VV2+ and VV2-, EV1+ and EV1-, or EV2+ and EV2- (2) Between NE+ and NE- |
| Tester Ranges | 5 V/DIV., 20 ms./DIV. |
| Conditions | Idling |
![]() |
WAVEFORM 6
Igniter IGT signal (from ECM to igniter) (1)
Igniter IGF signal (from igniter to ECM) (2)
| ECM Terminal Names | (1) Between IGT (1 to 6) and E1 (2) Between IGF1 and E1 |
| Tester Ranges | 2 V/DIV., 20 ms./DIV. |
| Conditions | Idling |
![]() |
WAVEFORM 7
Purge VSV for EVAP system operation signal
| ECM Terminal Names | Between PRG and E1 |
| Tester Ranges | 10 V/DIV., 50 ms./DIV. |
| Conditions | Idling |
![]() |
WAVEFORM 8
Vehicle speed signal
| ECM Terminal Names | Between SPD and E1 |
| Tester Ranges | 2 V/DIV., 20 ms./DIV. |
| Conditions | Driving at 12 mph (20 km/h) |
![]() |
WAVEFORM 9
Throttle drive motor operation signal (positive terminal)
| ECM Terminal Names | Between M+ and ME01 |
| Tester Ranges | 5 V/DIV., 1 ms./DIV. |
| Conditions | Idling with warm engine |
![]() |
WAVEFORM 10
Throttle drive motor operation signal (negative terminal)
| ECM Terminal Names | Between M- and ME01 |
| Tester Ranges | 5 V/DIV., 1 ms./DIV. |
| Conditions | Idling with warm engine |
![]() |
WAVEFORM 11
Engine speed signal
| ECM Terminal Names | Between TACH and E1 |
| Tester Ranges | 5 V/DIV., 10 ms./DIV. |
| Conditions | Idling |
![]() |
WAVEFORM 12
CAN communication signal
| ECM Terminal Names | Between CANH and E1 |
| Tester Ranges | 1 V/DIV., 10 μsec./DIV. |
| Conditions | Engine stops and ignition switch to the ON position |
![]() |
WAVEFORM 13
CAN communication signal
| ECM Terminal Names | Between CANL and E1 |
| Tester Ranges | 1 V/DIV., 10 μsec./DIV. |
| Conditions | Engine stops and ignition switch to the ON position |