Home › BRAKE › BRAKE › BRAKE PEDAL

BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY (for LHD)


    C132712
  1. Temporarily install the brake pedal support assembly with the bolt.

    NOTICE:
    Fully tighten the bolt after installing the brake booster assembly.



    C132711E01
  1. Temporarily install the No. 1 brake pedal support plate with 2 bolts (A) and bolt (B).

    NOTICE:
    Fully tighten 2 bolts (A) and bolt (B) after installing the brake booster assembly.

  1. Install the brake booster assembly (Click here).



    C132712
  1. Fully tighten the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



    C132711E01
  1. Fully tighten 2 bolts (A) and bolt (B).

    Torque:
    Bolt (A):
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }
    Bolt (B):
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    C132710E01
  1. Engage the 2 clamps and connect the stop light switch connector.



2. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY (for RHD)


    C132836E02
  1. Temporarily install the brake pedal support assembly with the bolt and install the clamp.



    C132837E01
  1. Temporarily install the No. 1 brake pedal support plate with 2 bolts (A) and bolt (B).

    NOTICE:
    Fully tighten 2 bolts (A) and bolt (B) after installing the brake booster assembly.

  1. Install the brake booster assembly. (Click here)



    C132836E01
  1. Fully tighten the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



    C132837E02
  1. Fully tighten 2 bolts (A) and bolt (B).

    Torque:
    Bolt (A):
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }
    Bolt (B):
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    C133309
  1. Connect the stop light switch connector.

  1. Install the accelerator pedal with the 2 bolts.



    C132839E01
  1. Connect the 2 connectors.



3. INSTALL BRAKE BOOSTER ASSEMBLY

HINT:
Refer to the procedures up to "INSTALL BRAKE BOOSTER". (Click here)



4. INSTALL ACCELERATOR PEDAL ROD (for RHD)

NOTICE:
  1. Avoid physical shock to the accelerator pedal assembly.
  2. Do not disassemble the accelerator pedal assembly.



    A135676
  1. Install the accelerator pedal rod with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the accelerator pedal position sensor connector.



5. INSTALL HEADLIGHT LEVELING ECU ASSEMBLY


    E129961E01
  1. Install the headlight leveling ECU assembly with the bolt.

  1. Connect the connector.



6. INSTALL COMBINATION METER ASSEMBLY


    B133987E01
  1. Connect each connector.

  1. Install the combination meter assembly with the 4 screws <E>.



7. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1


    B133985E01
  1. Engage the guide and the 4 claws.

  1. Install the instrument cluster finish panel with the 2 clips.



8. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL


    B144612
  1. Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.



9. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector.



    B133986
  1. Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.



10. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH


    B147263E01
  1. Install the air hose and connect the connector.

  1. Engage the 2 claws and the DLC3.

  1. Engage the claw and the 4 clips.

  1. Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.



11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY


    B132116E01
  1. Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.



12. INSTALL FRONT DOOR SCUFF PLATE


    B132067
  1. Engage the 7 claws and 3 clips, then install the front door scuff plate LH.