BRAKE MASTER CYLINDER > INSTALLATION |
| 1. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for LHD) |
![]() |
Install the gasket, the brake master cylinder sub-assembly and the front brake tube way with the 2 nuts.
Connect the connector.
![]() |
Install the brake master cylinder to way tube and temporarily tighten the 6 brake lines.
![]() |
Using the SST, fully tighten the 6 brake lines.
| 2. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for RHD) |
![]() |
Install the O-ring, vacuum check valve bracket, and the brake master cylinder sub-assembly with the 2 nuts.
![]() |
Temporarily tighten the 2 brake lines.
![]() |
Using the SST, fully tighten the 2 brake lines.
![]() |
Connect the connector.
| 3. CONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle) |
Connect the clutch reservoir tube to the brake master cylinder sub-assembly and move the clip.
| 4. FILL RESERVOIR WITH BRAKE FLUID |
![]() |
Fill the reservoir with brake fluid.
| 5. BLEED MASTER CYLINDER |
Using SST, disconnect the 2 brake lines from the master cylinder.

![]() |
Slowly depress the brake pedal and hold it (*1).
![]() |
Cover the 2 outer holes with fingers, and release the brake pedal (*2).
Repeat (*1) and (*2) 3 or 4 times.
Using SST, connect the 2 brake lines to the master cylinder.

| 6. BLEED BRAKE LINE |
![]() |
Connect a vinyl tube to the bleeder plug.
Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (*3).
![]() |
When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*4).
Repeat (*3) and (*4) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedure for each wheel to bleed the air from the brake line.
| 7. BLEED BRAKE ACTUATOR ASSEMBLY (w/ VSC) |
Depress the brake pedal more than 20 times with the ignition switch off.
![]() |
Connect the intelligent tester to the DLC3, then turn the ignition switch on (IG).
Turn the intelligent tester on and select "AIR BLEEDING" on the screen.
Bleed the air according to "Step 1: Increase" on the intelligent tester display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*5).
![]() |
When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*6).
Repeat (*5) and (*6) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedure for the rest of the wheels to bleed the air from the brake line.
Bleed the air from the suction line according to "Step 2: Inhalation" on the intelligent tester display.
![]() |
Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.
Operate the brake actuator assembly to bleed the air using the intelligent tester (*7).
![]() |
Check that the operation has stopped by referring to the intelligent tester display and tighten the bleeder plug (*8).
Repeat (*7) and (*8) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
For the rest of the wheels, bleed the air in the same way as stated in the above procedure.
Bleed the air from the pressure reduction line according to "Step 3: Decrease" on the intelligent tester display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Loosen the bleeder plug (*9).
Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal, and hold it.
![]() |
Tighten the bleeder plug, then release the brake pedal (*10).
Repeat steps (*9) to (*10) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedures for the rest of the brakes to bleed the air from the brake line.
Bleed the air from the brake line again according to "Step 4: Increase" on the intelligent tester display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*11).
![]() |
When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*12).
Repeat (*11) and (*12) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedures for each brake to bleed the air from the brake line.
Finish "AIR BLEEDING" on the intelligent tester and turn off the tester.
Disconnect the intelligent tester from the DLC3.
Turn the ignition switch off.
| 8. BLEED AIR FROM CLUTCH LINE (for Manual Transaxle) |
Fill the brake reservoir with brake fluid and bleed the clutch system.
| 9. INSPECT FLUID LEVEL IN RESERVOIR |
![]() |
Check the fluid level.
If brake fluid level is lowered, check for leakage and inspect the disc brake pad. If necessary, refill the reservoir with brake fluid after repair and replacement.
| 10. CHECK FOR BRAKE FLUID LEAKS |
| 11. INSTALL COWL TOP OUTER FRONT PANEL SUB-ASSEMBLY |
![]() |
Install the cowl top outer front panel sub-assembly with the 4 nuts, the 4 bolts and the clamp.
| 12. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Install the windshield wiper motor and link assembly with the 4 bolts.
![]() |
Connect the connector.
| 13. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Engage the 4 claws and install the cowl top ventilator louver sub-assembly.
Install the 2 clips.
| 14. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Engage the claw and install the front fender to cowl side seal LH.
| 15. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Engage the claw and install the front fender to cowl side seal RH.
| 16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
Clean the wiper arm serrations.
When reinstalling:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 37 to 52 mm (1.46 to 2.05 in.) |
| 17. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
Clean the wiper arm serrations.
When reinstalling:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 23 to 38 mm (0.90 to 1.49 in.) |
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 18. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for LHD) |
| 19. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for LHD) |
Install the air cleaner filter element onto the air cleaner case.
![]() |
Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.
![]() |
Align the matchmarks of the No. 1 air cleaner hose and throttle body, and then connect the air cleaner hose No. 1 to the throttle body and unfasten the No. 1 air cleaner hose clamp.
![]() |
Connect the No. 2 ventilation hose to the air cleaner hose.
![]() |
Connect the purge line hose to the clamp (*1).
Connect the 2 purge VSV vacuum hoses (*2).
Connect the purge VSV connector (*3).
Connect the mass air flow meter connector (*4).