PARKING BRAKE PEDAL > REMOVAL |
| 1. PRECAUTION |
| 2. PRECAUTION (w/ Navigation System for HDD) |
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 6. REMOVE FRONT DOOR SCUFF PLATE RH |
| 7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower instrument panel finish panel LH.
| 9. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the 3 claws and the 2 clips.
Disconnect each connector and remove the instrument panel sub-assembly.
| 10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for RHD) |
| 11. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1 (for RHD) |
![]() |
Remove the 2 clips.
Disengage the guide and 4 claws and then remove the instrument cluster finish panel.
| 12. REMOVE COMBINATION METER ASSEMBLY (for RHD) |
![]() |
Remove the 4 screws <E>.
Disconnect each connector and remove the combination meter assembly.
| 13. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides and remove the No. 2 under cover sub-assembly.
| 14. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Remove the bolt <A>.
![]() |
Remove the 4 screws <B>.
Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.
| 15. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 16. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
| 17. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
| 18. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY |
![]() |
Disengage the 6 claws and the 3 clips, and then remove the floor shift position indicator housing sub-assembly.
with Seat Heater System:
Disconnect each connector.
| 19. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY |
![]() |
Disengage the 3 claws and the 5 clips.
Disconnect the connector and remove the upper console rear panel sub-assembly.
| 20. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the upper console panel sub-assembly.
| 21. REMOVE CONSOLE BOX POCKET |
Remove the console box pocket.
| 22. REMOVE CONSOLE BOX CARPET |
![]() |
Remove the console box carpet.
| 23. REMOVE CONSOLE BOX ASSEMBLY |
![]() |
Remove the 2 screws <F>.
![]() |
Remove the 2 bolts <G> and the console box assembly.
| 24. REMOVE NO. 2 CONSOLE BOX INSERT FRONT |
![]() |
Remove the 3 screws <F>.
Disengage the clip and remove the No. 2 console box insert front.
| 25. REMOVE NO. 1 CONSOLE BOX INSERT FRONT |
![]() |
Remove the 3 screws <F>.
Disengage the clip and remove the No. 1 console box insert front.
| 26. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct) |
![]() |
Remove the clip and No. 1 console box duct.
| 27. REMOVE FLOOR CARPET BRACKET LH |
![]() |
Release the clamp.
Turn back the floor carpet.
![]() |
Remove the 3 clips.
Remove the floor carpet bracket LH.
| 28. REMOVE FLOOR CARPET BRACKET RH |
![]() |
Release the clamp.
Turn back the floor carpet.
![]() |
Remove the 3 clips.
Remove the floor carpet bracket RH.
| 29. REMOVE YAW RATE AND ACCELERATION SENSOR (w/ VSC) |
![]() |
Disconnect the yaw rate and acceleration sensor connector.
Remove the 2 bolts and yaw rate and acceleration sensor.
| 30. REMOVE FLOOR SHIFT LEVER ASSEMBLY |
![]() |
Remove the 4 bolts and the floor shift lever assembly.
| 31. REMOVE CENTER AIRBAG SENSOR ASSEMBLY |
Turn back the carpet.
![]() |
Disconnect the holder (with connectors).
Remove the 3 bolts and center airbag sensor assembly.
| 32. DISCONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Using a wrench, hold the lock nut and loosen the turnbuckle.
Disconnect the No. 4 parking brake cable assembly from the No. 1 parking brake cable assembly.
| 33. REMOVE PARKING BRAKE PEDAL ASSEMBLY (for LHD) |
![]() |
Using needle-nose pliers, remove the clip from the No. 1 parking brake cable assembly.
Remove the bolt, nut, and the No. 1 parking brake cable clamp.

Separate the No. 1 parking brake cable assembly from the body.
![]() |
Disconnect the parking brake switch connector.
Remove the bolt, 2 nuts, and the parking brake pedal assembly with the No. 1 parking brake cable assembly from the body.
| 34. REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the 3 claws and remove the No. 1 air duct sub-assembly.
| 35. REMOVE PARKING BRAKE PEDAL ASSEMBLY (for RHD) |
![]() |
Using needle-nose pliers, remove the clip from the No. 1 parking brake cable assembly.
![]() |
Remove the bolt.
![]() |
Disconnect the parking brake switch connector.
Remove the bolt, 2 nuts, and the parking brake pedal assembly with the No. 1 parking brake cable assembly from the body.