Home › BRAKE › PARKING BRAKE › PARKING BRAKE LEVER

PARKING BRAKE LEVER > INSTALLATION

for Preparation Click here



1. INSTALL PARKING BRAKE LEVER SUB-ASSEMBLY


    C131911
  1. Install the parking brake lever sub-assembly with the 2 bolts and the clip.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the parking brake switch connector.



2. INSTALL PARKING BRAKE EQUALIZER


    C132657
  1. Install the parking brake equalizer to the No. 1 parking brake cable assembly.



    C143741E01
  1. Slide the rubber boot back as shown in the illustration.



3. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY


    C138185
  1. Connect the No. 2 parking brake cable assembly to the parking brake equalizer.



4. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C138184
  1. Connect the No. 3 parking brake cable assembly to the parking brake equalizer.



5. INSTALL CROSS MEMBER FLOOR NO. 4 REINFORCEMENT SUB-ASSEMBLY


    C132658
  1. Install the cross member floor No. 4 reinforcement sub-assembly with the 8 bolts.



6. INSTALL FRONT FLOOR CARPET ASSEMBLY


  1. Engage the 6 clamps and the 2 claws and install the front floor carpet assembly.


    C132661E01



7. INSTALL LUGGAGE DOOR LOCK OPEN LEVER SUB-ASSEMBLY


    C132659
  1. Engage the claw and install the luggage door open lever sub-assembly with the screw.



8. INSTALL FRONT FLOOR CAUTION PLATE COVER


    C132660
  1. Engage the claw and the clip and install the front floor caution plate cover.



9. INSTALL LOWER CENTER PILLAR GARNISH LH


    B132058
  1. Engage the 2 claws and 2 clips, then install the lower center pillar garnish LH.



10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B132080E01
  1. Install the rear door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.



11. INSTALL REAR DOOR SCUFF PLATE LH


    B132068
  1. Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.



12. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B132081E01
  1. Install the front door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.



13. INSTALL FRONT DOOR SCUFF PLATE LH


    B132067
  1. Engage the 7 claws and 3 clips, then install the front door scuff plate LH.



14. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures for the RH side and the LH side.



15. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B132082E01
  1. Install the rear door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.



16. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B132083E01
  1. Install the front door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.



18. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



19. INSTALL NO. 2 CONSOLE BOX INSERT FRONT


    B134005E01
  1. Engage the clip.

  1. Install the No. 2 console box insert front with the 3 screws <F>.



20. INSTALL NO. 1 CONSOLE BOX INSERT FRONT


    B134006E01
  1. Engage the clip.

  1. Install the No. 1 console box insert front with the 3 screws <F>.



21. INSTALL FLOOR CARPET BRACKET LH


22. INSTALL FLOOR CARPET BRACKET RH


23. INSTALL CONSOLE BOX ASSEMBLY


    B134002E01
  1. Install the 2 screws <F>.



    B134003E01
  1. Install the console box assembly with the 2 bolts <G>.



24. INSTALL CONSOLE BOX CARPET


    B134004
  1. Install the console box carpet.



25. INSTALL CONSOLE BOX POCKET
  1. Install the console box pocket.



26. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Connect each connector.



    B133997E01
  1. Engage the 4 claws.

  1. Install the upper console panel sub-assembly with the 2 screws <F>.



27. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY


    B137277
  1. Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.



28. INSTALL UPPER CONSOLE PANEL


    B137276
  1. Engage the 2 claws and the 5 clips to install the upper console panel as shown in the illustration.



29. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226063
  1. Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.



30. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226064
  1. Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.



31. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B137273
  1. Install the shift lever knob sub-assembly.



32. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B133992E01
  1. Engage the 3 claws and 3 clips.

  1. Install the 4 screws <B>.

  1. Install the lower instrument panel sub-assembly with the bolt <A>.



33. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY


    B133989E01
  1. Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover.



34. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH


    B147263E01
  1. Install the air hose and connect the connector.

  1. Engage the 2 claws and the DLC3.

  1. Engage the claw and the 4 clips.

  1. Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.



35. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B132116E01
  1. Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.



36. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



37. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

HINT:
Refer to the procedures up to "INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)". (Click here)



38. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

HINT:
Refer to the procedures up to "INSTALL FRONT SEAT ASSEMBLY (for Power Seat)". (Click here)



39. INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

HINT:
Use the same procedures for the RH side and the LH side.



40. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:
Use the same procedures for the RH side and the LH side.