PARKING BRAKE LEVER > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat) |
| 3. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat) |
| 4. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat) |
| 5. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat) |
| 6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 8. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides and remove the No. 2 under cover sub-assembly.
| 9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower instrument panel finish panel LH.
| 10. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Remove the bolt <A>.
![]() |
Remove the 4 screws <B>.
Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.
| 11. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 12. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
| 13. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
| 14. REMOVE UPPER CONSOLE PANEL |
![]() |
Open the lid of the upper console panel.
Apply protective tape to the area shown in the illustration.
![]() |
Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.
with Seat Heater System:
Disconnect each connector.
| 15. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY |
![]() |
Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.
| 16. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the upper console panel sub-assembly.
| 17. REMOVE CONSOLE BOX POCKET |
Remove the console box pocket.
| 18. REMOVE CONSOLE BOX CARPET |
![]() |
Remove the console box carpet.
| 19. REMOVE CONSOLE BOX ASSEMBLY |
![]() |
Remove the 2 screws <F>.
![]() |
Remove the 2 bolts <G> and the console box assembly.
| 20. REMOVE FLOOR CARPET BRACKET LH |
![]() |
Release the clamp.
Turn back the floor carpet.
![]() |
Remove the 3 clips.
Remove the floor carpet bracket LH.
| 21. REMOVE FLOOR CARPET BRACKET RH |
![]() |
Release the clamp.
Turn back the floor carpet.
![]() |
Remove the 3 clips.
Remove the floor carpet bracket RH.
| 22. REMOVE NO. 2 CONSOLE BOX INSERT FRONT |
![]() |
Remove the 3 screws <F>.
Disengage the clip and remove the No. 2 console box insert front.
| 23. REMOVE NO. 1 CONSOLE BOX INSERT FRONT |
![]() |
Remove the 3 screws <F>.
Disengage the clip and remove the No. 1 console box insert front.
| 24. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 25. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 26. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Disengage the 5 claws and 2 clips, and remove the rear door scuff plate LH.
| 27. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
| 28. REMOVE LOWER CENTER PILLAR GARNISH LH |
![]() |
Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.
| 29. REMOVE FRONT DOOR SCUFF PLATE RH |
| 30. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 31. REMOVE REAR DOOR SCUFF PLATE RH |
| 32. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 33. REMOVE LOWER CENTER PILLAR GARNISH RH |
| 34. REMOVE FRONT FLOOR CAUTION PLATE COVER |
![]() |
Disengage the clip and the claw and remove the front floor caution plate cover.
| 35. REMOVE LUGGAGE DOOR LOCK OPEN LEVER SUB-ASSEMBLY |
![]() |
Remove the screw.
Disengage the claw and remove the luggage door open lever sub-assembly.
| 36. REMOVE FRONT FLOOR CARPET ASSEMBLY |
Disengage the 6 clamps and the 2 claws.

Turn back the front floor carpet assembly until the bolts of the cross member floor No. 4 reinforcement sub-assembly can be seen.
| 37. REMOVE CROSS MEMBER FLOOR NO. 4 REINFORCEMENT SUB-ASSEMBLY |
![]() |
Remove the 8 bolts and the cross member floor No. 4 reinforcement sub-assembly.
| 38. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Loosen the lock nut and the No. 1 wire adjusting nut of the No. 1 parking brake cable assembly.
![]() |
Separate the No. 3 parking brake cable assembly from the parking brake equalizer.
| 39. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY |
![]() |
| 40. REMOVE PARKING BRAKE EQUALIZER |
![]() |
Slide the rubber boot as shown in the illustration.
![]() |
Remove the parking brake equalizer from the No. 1 parking brake cable assembly.
| 41. REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY |
![]() |
Disconnect the parking brake switch connector.
Remove the 2 bolts, the clip, and the parking brake lever.