KNOCK SENSOR > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
| 2. REMOVE ENGINE UNDER COVER LH |
| 3. REMOVE ENGINE UNDER COVER RH |
| 4. DRAIN ENGINE COOLANT |
Remove the radiator cap sub-assembly from the radiator assembly.
Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs, then drain the coolant.

| 5. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut and the front wiper arm and blade assembly LH.
| 6. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut and the front wiper arm and blade assembly RH.
| 7. REMOVE FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Disengage the claw and remove the front fender to cowl side seal LH.
| 8. REMOVE FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Disengage the claw and remove the front fender to cowl side seal RH.
| 9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Remove the 2 clips.
Disengage the 4 claws and remove the cowl top ventilator louver sub-assembly.
| 10. REMOVE WINDSHIELD WIPER MOTOR AND LINK |
![]() |
Disconnect the connector.
![]() |
Remove the 4 bolts and the windshield wiper motor and link assembly.
| 11. REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY |
![]() |
Install the cowl top panel outer sub-assembly with the 4 bolts and 4 nuts.
| 12. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 7 clips and intake duct seal.
| 13. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.
| 14. REMOVE AIR CLEANER INLET ASSEMBLY |
![]() |
Remove the 2 bolts, clamp and air cleaner inlet.
| 15. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner cap sub-assembly, and connect the 3 bands.
![]() |
Connect the mass air flow meter connector (*1).
Connect the No. 2 ventilation hose (*2).
Connect the hose band (*3).
![]() |
Connect the 3 vacuum hoses.
| 16. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Disconnect the vacuum hose and hose clamp.
Remove the 3 bolts and air cleaner case.
| 17. REMOVE NO. 1 AIR CLEANER INLET |
![]() |
Remove the bolt and No. 1 air cleaner inlet.
| 18. REMOVE INTAKE AIR SURGE TANK |
![]() |
Disconnect the 2 water by-pass hoses from the throttle with motor body assembly. (*1)
Disconnect the vapor feed hose. (*2)
Disconnect the throttle with motor body assembly connector and clamp. (*3)
![]() |
Disconnect the No. 1 ventilation hose. (*4)
Disconnect the union to check valve hose. (*5)
![]() |
Remove the bolt and vacuum hose clamp.
![]() |
Disconnect the connector.
![]() |
Using a 5 mm socket hexagon wrench, remove the 4 bolts. (*1)
Remove the 2 nuts, 2 bolts and intake air surge tank. (*2)
Remove the gasket from the intake air surge tank.
| 19. DISCONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Remove the No. 2 fuel pipe clamp.
Pinch the tube connector and then pull out the fuel pipe.
| 20. REMOVE INTAKE MANIFOLD |
![]() |
Uniformly loosen and remove the 6 bolts and 4 nuts.
Remove the intake manifold and 2 gaskets.
| 21. REMOVE KNOCK CONTROL SENSOR |
![]() |
Disconnect the 2 knock control sensor connectors.
Remove the 2 bolts and 2 knock control sensors.