Home › ENGINE ยท 2GR-FE › ENGINE CONTROL SYSTEM › ECM

ECM > INSTALLATION

for Preparation Click here



1. INSTALL ECM


    A135713
  1. Install the ECM bracket with the 4 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



    A135712
  1. Connect the 2 connectors.



    A135711
  1. Install the ECM with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



2. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY


    A136272
  1. Install the cowl top panel outer sub-assembly with the 4 bolts and 4 nuts.

    Torque:
    Bolt:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Nut:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }



3. INSTALL WINDSHIELD WIPER MOTOR AND LINK


    E128813E01
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration.



    E128812
  1. Connect the connector.



4. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E128811
  1. Engage the 4 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.



5. INSTALL FRONT FENDER TO COWL SIDE SEAL RH


    E128810
  1. Engage the claw and install the front fender to cowl side seal RH.



6. INSTALL FRONT FENDER TO COWL SIDE SEAL LH


    E128809
  1. Engage the claw and install the front fender to cowl side seal LH.



7. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



    E112237E01
  1. Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.



    E128820E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    37 to 52 mm (1.46 to 2.05 in.)



8. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



    E112237E01
  1. Clean the wiper arm serrations.

  1. When reinstalling:

    1. Clean the wiper pivot serrations with a wire brush.



    E128821E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.
    Area
    Measurement
    A
    23 to 38 mm (0.90 to 1.49 in.)

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL